Shocking kills algae and germs but doesn't get rid of them. Running the filtration pump for 24 hours clears the contaminant and ensures your pool is clean. If the pool is still cloudy or green, adjust the chemical levels, then scrub and manually remove any debris within your sight.
Adding more chlorine to your pool will kill bacteria, pollutants and any other unwanted organisms in the water. Most people wait until they have a cloudy pool or pool algae to shock their pool. However, adding shock to your pool on a regular basis can help you avoid pool water problems.
In summary, if your combined chlorine reads above 0.5 ppm, your water may turn cloudy and become unsafe for swimming. If this is the case, you need to shock your pool immediately to clear it.
The best time of day to shock your pool is in the evening. This is because the sun's rays can affect the effectiveness of the chlorine by dissolving it too quickly, before it has a chance to rid the pool of contaminants and clean the water.
Sun Down – You'll want to shock your pool in the evening when the sun has gone down. This gives your pool plenty of time during the night to free the chlorine and clean the water. In the morning, you should be able to enjoy your pool. If you shock your pool during the day, the sun's UV rays will dissolve the chlorine.
Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you're using.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
Chlorine is a sanitizer, and (unless you use Baquacil products) is necessary for maintaining a clear and healthy pool. Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly.
High doses of chlorine, like pool shock, can cause temporary cloudiness as it kills contaminants. High levels of pH, alkalinity, and calcium hardness are more likely to cause cloudy water.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
You should wait at least 8 hours before shocking your pool again. You really need to wait long enough for the shock to circulate and mix thoroughly. If you wait this long and need to add more shock, go right ahead. You can't over shock your pool.
Skim the top of the pool for debris that may have settled on the pool surface. Add one pound of diluted granular shock to the water for every 7,000 gallons of pool water. Run the filter for 24 hours and retest the water. The slimy looking film can be an early onset of algae.
Run your filtration system for eight hours every day over summer. Back-wash it if you have a sand filter and clean cartridges with Filtrite Filter Cleaner and Degreaser. Add 50 grams of Sanit-eezy Performance per 10,000 litres of pool water. No-one should swim for at least 30 minutes after this.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool. Short answer: No. Chlorine sanitizers and shock are similar but different in strength.
Never add chemicals at the same time, whether you're balancing the water, shocking the pool, or adding a specialty chemical. For most water balance changes, the pump needs to run on the high setting for at least four hours before you can add another chemical or retest the water.