To truly be a Paver Whisperer, you must make sure the sealer is applied evenly to the surface. Using the spray technique and back rolling any puddles will result in a smoother application and a smoother finished product.
One of the best paver sealers is the Siloxa-Tek 8500. It is a penetrating concrete sealer designed to treat a variety of applications with an emphasis on hydrophobicity and reduction of water uptake. It dries completely clear with a natural finish that will not change the look or appearance of the susbtrate.
It's Easier Than You Think To Seal Your Pavers
Spray apply rather than roller apply. Use water based sealers rather than solvent based. Use urethane sealers rather than acrylic sealers.
Should Pavers Be Dry Before The Sealing Proccess? Yes, it is important to ensure that your pavers and your pool deck are dry before applying sealer. If they are wet, the sealer will not be able to adhere properly and could eventually peel off and cause damage to the pavers.
If the sealer is not cured correctly, water can cause white marks or stains on your pavers and can even be trapped beneath the layer of sealer. It is very important not to walk or drive on sealed pavers at least 24-48 hours after application. A protective sealer enhances the natural color and beauty of your pavers.
What are the ideal weather conditions for sealing? Ideal conditions would be 75 degrees and sunny; however, anywhere between 50-90 degrees is generally fine. Take note that solvent-based sealants evaporate faster, so lower temperatures are better for application.
Enhanced aesthetic: The paver sealer enhances the curb appeal of your properties and provides perfect finish to the paved areas and at the same time stabilizes the joint sand by locking it in place. It protects the pavement against harmful UV rays and prevents fading.
You need 48 hours of dry weather after your sealer has been applied to cure it. (Remember to turn off your automatic water sprinklers.) If the sealer is not cured correctly, water can cause white marks or stains on your pavers and can even be trapped beneath the layer of sealer.
How Much Does It Cost to Clean and Reseal Pavers per Square Foot? In total, you should expect to pay around $2 per square foot to clean and seal pavers. The price may vary between $1 and $3 per square foot, depending on the sealant and method of cleaning.
Understandably, some will think this indicates the blocks are in some way faulty, sub-standard or iffy, but that's not necessarily the case. The cause for this visible difference in appearance is most commonly* a variation in the concrete used to make the blocks.
Most contractors and manufacturers recommend sealing pavers for the many benefits. Both concrete and brick pavers are porous materials that can change quality and appearance when they absorb liquids.
For best results the sand should be dry to its full depth before sealing. It is always recommended to test the sealer of choice in a small area first. Always read product label and directions carefully before beginning to use any sealer products.
We alway recommend 2 coats of sealer for optimum performance.
You pressure clean the pavers, re-sand the paver joints and then apply two coats of your favorite paver sealer and the job was complete.
Never Too Late to Seal Pavers
It's always best to seal soon after a new installation. But, our proven system of repairing, cleaning and sealing will also bring back the original luster to old, dirty and fading pavers. Sealing is the final step in a comprehensive process.
Choosing to seal your pavers will keep your color consistent and un-faded. Not only does choosing to seal your pavers keep the color untouched, but it can also increase the vibrancy of your colors. One largely agreed upon benefit of sealers is that they limit stains.
You're wondering what happens if you don't seal pavers. Your pavers won't disintegrate if you don't seal them, but they'll likely fade much sooner than if you applied sealant. You'll also need to clean them more often, and the stains won't be as easy to remove.
How Often to Seal Pavers. Generally speaking, you should seal your pavers every 3-5 years. You will notice if and when your pavers begin to fade or show signs that they need resealing.
Your concrete pavers will look better than new. 5 gal. bucket covers approximately 500 sq. ft.
How long should I wait before sealing my new pavers? Typically 60-90 days. The main reason to wait is so that efflorescence can work its way to the surface and be cleaned off. The more the pavers get wet, the quicker this happens.