Carpet Cleaning Process To clean your carpet, we use hot water extraction. Unlike other carpet cleaning methods used by other companies, like carpet shampooing or dry cleaning, hot water extraction won't damage your carpet fibers or leave behind any residue.
Absolutely! Hot water extraction is a versatile and safe cleaning method for a variety of carpet types, from synthetic fibers to natural wool.
The Best Carpet Cleaning Process found by Nationwide Consumer Testing is the Circular Dry-Foam Carpet Cleaning Method. The Circular Dry-Foam Carpet Cleaning Method had a very high level of soil removal (92.3%) with little or no soap residue. It doesn't use harsh detergents which are oily or sticky.
Hot water extraction (steam cleaning) is one of the most effective ways to clean carpets. It relies on pressurized water heated to extreme temperatures to rinse cleaning agents out of the carpet. After the cleaning process is complete, the carpet typically takes 6 to 12 hours to dry.
What's the difference between Hot and Cold-Water Extractors? Hot water extractors combine hot water with high psi pressure (and chemicals) to clean and sanitize carpets, and remove any chemical residue. Cold water extractors combine water with high psi pressure (and chemicals) to clean carpets and floors.
Carpet Cleaning Process
We start cleaning by spot treating any areas that need extra attention. Then, we will use our patented carpet cleaning machines to deep clean. These machines pump hot water into your carpet to release any dirt deep within the fibers, then extract the water and remove the dirt.
If your carpet is crunchy after getting cleaned, that means that particles of the shampoo, detergent, or chemicals that were used during the cleaning process were left behind in the carpet fibers.
Carpet manufacturers typically recommend a weekly surface clean and a deep clean at least once every 12 to 18 months. Hubert Miles, Certified Master Inspector and owner of Patriot Home Inspections in South Carolina, shares why.
The best method for sterilizing carpet without hiring a professional is to mist the surface of the carpet with a mixture of white vinegar diluted with water and allow it to sit overnight. Then you can steam clean your carpet using the manufacturer's instructions on your machine.
The method we use for carpet cleaning is hot water extraction, commonly referred to as steam cleaning. Stanley Steemer's exclusive hot water extraction method removes the toughest, deepest dirt safely and gently. Hot, soft water and a specially formulated cleaning solution are injected deep within the carpet fibers.
Hot Water Extraction (HWE) is a method of carpet cleaning. It involves a combination of hot water and cleaning agents being injected into the fibers of a carpet at high pressure and the lifted soil being removed by a powerful vacuum.
Best practices for safety after carpet cleaning
To ensure your safety and comfort after carpet treatment, it's important to follow a few best practices. First, allow sufficient drying time, ideally, wait at least 6 to 8 hours before re-entering the room, and aim for 24 hours for complete dryness.
Stanley Steemer, a professional water restoration company, pumps out freestanding water quickly and then extracts water from carpet, padding, upholstery, hardwood and tile.
So, which cleaning method do we think cleans better? Honestly, steam cleaning is the preferred method for most residential and commercial “wall-to-wall” carpet.
Step 1: Mix a litter of water with a modest bit of fabric softener in a bucket or spray bottle—one to two tablespoons. Step 2: lightly mist the afflicted carpet sections with the solution. Don't overhydrate. Step 3: Use a fresh towel to wipe any extra moisture.
The traditional method of cleaning and rinsing your carpet will leave soap and shampoo residue that will turn into mildew over time. As a consequence, it will quickly become covered in dust and dirt. In high-traffic areas with a lot of footfall, this can get out of hand quickly.
Too Much Moisture
Moisture often causes carpet buckling after cleaning. Wet carpets—from cleaning or spills—allow water to soak into the fibers, making them expand.
Hot water extraction does not damage carpet fibres because it only uses hot water, pressure, and cleaner to leave your carpet looking its absolute best.
On average, professional carpet cleaning costs $150-$200, says David Steckel, home care expert at Thumbtack. “Carpet cleaning services may charge anywhere from $89-$109 on the low end and $300-$400 on the high end,” Steckel says.
Steam cleaning uses higher temperature water, around 212 degrees Fahrenheit, to produce steam, whereas hot water extraction uses water that's 110-165 degrees Fahrenheit. Also, no rinsing is involved with steam cleaning. We clean carpet exclusively using hot water extraction and our patented cleaning equipment.
Take a bath or shower
Taking a hot bath or shower for 15 minutes can help your mind and muscles relax. If you have access to a sauna or steam room, it can have the same effect. These heated environments help your blood vessels to dilate, or open up, which lowers your blood pressure.
When water's excessively hot it can strip away the natural oils from your skin, leading to dryness and possible irritation. And soaking in water that's far too hot can lead to dehydration, dizziness, and even fainting, which is certainly not what you've stepped into the bath for at the end of the day.
Improve circulation
Cold water strains your body — it goes into “survival mode,” working hard to maintain its core temperature. This stimulates your body to increase blood flow circulation. “Increasing circulation redistributes blood and delivers freshly oxygenated blood to areas of the body that need to recover,” Dr.