Is 40 psi good for a sprinkler system?

Author: Miss Telly Sporer IV  |  Last update: Tuesday, August 26, 2025

Sprinkler heads are rated at a specific GPM flow rate at a specific pressure. We recommend that you use 40 psi when designing your system.

Is 40 psi enough for a sprinkler system?

Most spray and rotator heads are designed to work their best at about 30 psi. When pressure is lower, the watering radius will be reduced, so you may need to place your heads closer together to get the coverage you need. Higher pressures – those above about 40 psi – will cause the head to mist or fog.

How many psi does a sprinkler system need?

For spray heads, it is 30 psi, with an operating range of 15 to 30 psi. For drip lines, this is about 20 psi, with an operating range of 15 to 30 psi. Remember, flow rate and pressure are directly related to one another. If pressure is not well-controlled, irrigation efficiency will suffer.

Is 40 psi normal water pressure?

Normal water pressure range

In general, residential water pressure ranges between 45-80 psi (pounds per square inch). If your water pressure is under 40 psi, it's considered low. A psi between 20-30 is considered very low, and under the minimum water pressure required by most building codes.

How much psi do I need to flush my sprinkler system?

The recommended PSI ratings for blowouts are not to exceed 50 PSI for general safety and efficiency. Never exceed this PSI when the system is using PVC piping, or you can crack the pipes. If nothing else, absolutely do not run any compressor higher than 80 PSI in your lines, or damage will be more than likely to occur.

Sprinkler System Valve Pressure Regulator

What is the best psi for blowing out sprinklers?

This will result in the remaining water draining into low spots and subjecting the system to freeze damage. Ideal pressures are in the range of 40 to 80 pounds per square inch (psi) for the air compressor with 80 psi being the maximum for rigid PVC pipe and 50 psi for polyethylene pipe (flexible black pipe).

What is too much pressure in a sprinkler system?

High water pressure can be caused by high supply pressure or changes in landscape elevation. High pressure can be managed by installing pressure regulators on the main line near valves that separate irrigation zones or sprinkler bodies that have internal pressure regulation.

Is 50 PSI enough water pressure for a sprinkler system?

Keep in mind that sprinkler and drip systems will not work properly if the pressure is too low or too high. Most sprinkler systems work at an optimal pressure of 30-50 psi, and most drip systems work best in the range of 20-40 psi.

Is 40 PSI too high?

Tire pressure increases when the tires are used, and for this reason, following the vehicle and tire brands' recommendation is crucial. Typically, if the recommended pressure levels are 35, then the tires should not use more than 40 psi. More than that will result in the before mentioned problems.

How high will 40 PSI lift water?

If the gauge reads 40 PSI when the hose is filled with water, we know that the elevation is 92.4 feet. We simply take 40 PSI x 2.31 which equals 92.4. This is not distance, but feet of head.

Is 80 psi too high for a sprinkler system?

Pressures higher than 80 psi can possibly damage household appliances. Generally, the ideal pressure is 65 psi. A pressure regulating valve (PRV) can be used to reduce if the pressure is higher than 65 psi.

How much psi does a sprinkler system need?

Average Water Pressure For A Sprinkler System

Water pressure is measured in pounds per square inch. For residential and small business applications manufacturers recommend 30psi at the head for sprays and 45 psi at the head for rotors. Larger heads will require higher pressure.

How many sprinkler heads per zone with 40 psi?

We recommend that you use 40 psi when designing your system. Example: if your sprinkler heads use 2.5 gpm @ 40 psi, then a ¾” service (20 gpm) could operate approximately 8 heads at one time. Based on this example calculation, you would not have more than 8 heads on at one time.

Is 40 psi OK for drip irrigation?

A reading of 30 to 40 psi is considered safe for you to attach your drip irrigation system directly to the water source. Do take into consideration that home water pressure will fluctuate. A pressure of 80 psi or more will stress the pipes and fixtures of most drip systems and can cause damage to your system.

Is 40 psi good water pressure?

Water Pressure Readings

Normal water pressure is generally between 40 and 60 PSI. Most homeowners prefer something right in the middle around 50 PSI. Once you measure the water pressure in your house, you can adjust it to a setting that is ideal for all family members and household uses.

What happens if your psi is too high?

One of the biggest risks with overinflated tires is experiencing a blowout. Tire blowouts can easily cause you to lose control of your vehicle and make it much harder to brake within a shorter distance, not only posing a safety threat to yourself but to others on the road, as well.

Is 40 psi too low?

If it gets too low, your safety—and the safety of others on the road—is impacted. Hence, maintaining the correct tire pressure (between 32 to 35 PSI is a good idea. Remember, anything lower than 20 PSI is considered a flat tire.

Do I need a pressure regulator for my sprinkler system?

You need pressure regulators to achieve the intended distribution pattern and application rate. If you do not control the system pressure, it can negatively affect the sprinkler performance. Without regulators, the throw radius can alter, fitting, and emitters could even take damage or blow out of the tubing.

What is the best sprinkler head for low water pressure?

Impact sprinklers are excellent for low-pressure water sources. This type of sprinkler is built with integrated regulation valves that control water flow. Using impact sprinklers will still allow you to achieve healthy growth of grass and plants, even if the water pressure in your house is less than ideal.

Can I run a sprinkler system off a well?

Overall, well water can be a great option for irrigation, but there are a few potential drawbacks to consider before making the switch. Because it is free and available in most areas, using well water for irrigation may be a tempting solution that can also help conserve municipal water sources.

What is the maximum allowable pressure for sprinkler?

Normal sprinklers are rated for 175 psi. High pressure sprinklers are rated for 250 Globe HP ARE 300 psi. There may be others that go 300, but they are costly.

What pressure should I test my sprinkler pipe?

Fire protection piping systems are pressure tested to reveal any leaks by pressurizing the piping to 200 psi for 2 hours. 2.

Previous article
How to tell if a stud wall is load-bearing?
Next article
What color bathroom sells the most?