Dampen a cotton ball or folded paper towel with isopropyl alcohol and place it against the glued-on area. Let the alcohol sit on the surface for about 5 minutes. Remove it and wipe the area down with warm, soapy water. The glue should be loosened enough to scrape away with the edge of a putty knife.
If you need to remove uncured/wet glue, we recommend wiping with a dry cloth or a cloth soaked in isopropyl alcohol. Once Gorilla Glue Clear is dry, it can only be removed by mechanical means: such as sanding, chiselling, scraping or picking.
Gorilla glue is a moisture activated polyurethane and can be softened/removed with acetone, nail polish remover.
Apply Heat. If you are dealing with a delicate surface and are unable to use adhesive remover, acetone, rubbing alcohol, etc., a bit of heat may do the trick, without damaging the surface. Some stubborn adhesives melt or soften and become much easier to remove when heated. Heat the adhesive using a heat gun.
Use a cotton ball soaked in pure acetone or nail varnish remover, and press it against the glue. Once it's dissolved, it should be easy to wipe away. Alternatively, try scraping away the glue. Use a putty knife or razor blade.
One easy method is to use standard cooking oil or oil-based materials. Vegetable or canola oil can work wonders, as can peanut butter or mayonnaise. Spread it on, let it soak into the residue for about an hour, then wipe it away. For a tougher clean, try rubbing alcohol or vodka.
If these methods do not work, you may need to try out a chemical that would dissolve the glue. Denatured alcohol or hydrogen peroxide are both good options to use to remove super glue from surfaces.
Gorilla Glue Original will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP) or polyethylene (PE) plastics or any type of rubber with high oil or plasticizer content.
Test it on an inconspicuous spot before beginning. Apply acetone. Pour it onto your cloth and rub it gently against the affected area to remove the super glue from the car dashboard. Acetone works quickly, so you should frequently check to see whether the glue is gone.
It easily lifts tape or sticky residue, and it can even remove crayons and glue from surfaces that you want clean. It's perfect for any sticky mess around the house. However, we don't recommend using Goo Gone on silk, leather, suede, rubber, faux stainless steel, drywall, unfinished wood, or unsealed stone.
Gorilla Super Glue can typically be exposed to temperatures ranging from -55° to 100° C. Too much exposure to water, especially warm water, can compromise the strength of the bond.
For cured super glue, fill a bowl with warm soapy water. Soak the cured area for several minutes. Gently wiggle the bonded area to allow the soapy water to penetrate the bond. The key is to be patient and NEVER pull the area apart.
Windex also works to help remove cyanoacrylate glues, also known as super glues, by weakening the glue's bonds and making it easier to gently scrape the glue off your glass.
Soak the glue residue in rubbing alcohol, acetone, or vinegar. Leave it soaked for a few minutes then try scraping it off again. If the glue still proves too stubborn, try heating it up with a hair dryer. This should help loosen up the glue.
Mix a few drops of paint thinner with the glue to soften it.
It is formulated to thin out paint, but it may also help you thin out hardened glue.
Blot the glue with acetone or rubbing alcohol and let this substance break down the glue. Clear away with a damp cloth. For fabric: Use acetone, but test sparingly first to avoid potential damage. Once the adhesive bond has begun to break, apply a pretreatment stain remover deep into the glue.
3M adhesive remover is amazing stuff. It beats Goo Gone by a wide margin, I recently used it to remove PETG residue from my 3D printer bed and that stuff is gnarly. 3M 38983 General Purpose Adhesive Remover - 12 oz. https://www.amazon.com/dp/B004EBNTYK/ref=cm_sw_r_cp_api_i_cU...