How Often Should You Backwash a Pool Sand Filter? As a general rule of thumb, you should backwash and rinse your filter about once a fortnight. The optimal time is right after you vacuum the pool. However, if your pool has had a lot more use than normal, it may be necessary to backwash once a week.
Rinse the filter for about 1 to 2 minutes or until the water in the sight glass is clear. NOTE: Any electric heater must be off. Stop the pump. Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds.
The 'Rinse' setting should be used after backwashing and again run just for a minute or two. On this setting the water is flowing through the filter in the normal direction but once again is being sent to the waste pipe rather than being returned to the pool.
Rinse: This cleans the water filled inside the filter tank. Circulate/Bypass/Recirculate: This setting is used when you need to return the water back into the pool without making it go through the filter. Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter.
In order to prevent residual blow back into the pool, once you've finished backwashing it's highly advisable to rinse the filter. Just as the backwash lifts and flushes the sand, the rinse resets the sand to its original position for optimum filtration.
You'll also need to vacuum to waste when there is a large amount of debris or leaves in the pool, usually at opening. Vacuuming to WASTE can only be accomplished if a multiport valve controls your pool filter system. This position bypasses the filter and sends all the unwanted debris through the waste line.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day. But here's the thing: you don't have to run your pool pump consecutively. You can choose to run it for three hours in the morning before you leave for work and another 5 hours in the evening.
Put your hand over the inlet (where the basket is located on the side of the pool, not the pump) to feel if there's enough suction. Your hand should be sucked up against the inlet fairly quickly if the pump is set to its highest mode. If it's barely pulling, you likely have a clogged filter or a leak in the line.
One of the most significant consumers of energy in homes with swimming pools are pool pumps, which keep pools clean by circulating water through filters. Pool pumps can consume 3,000 to over 5,000 kWh per year.
It's best to run your pool pump during the day
Not only does sunlight give fuel for algae to grow, it also destroys your pool chlorine and this is why you should always run your pool during the day!
Shock is liquid or granular chlorine. You should add one gallon (or one pound) of shock per 10,000 gallons of pool water every week to two weeks. During hot weather or frequent use, you may need to shock more frequently.
Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water.
The extra filtering will help clean out the impurities rain has introduced into your pool's water. Pool pumps are made to withstand rain and it is beneficial to run your pump during or after rain.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
Connecting the vacuum system to the pump.
Now, here answers the question earlier: do you leave skimmer basket in when vacuuming pool? YES, you need to remove the skimmer or strainer basket before attaching the open end of the hose to the inlet. Finally, plug the open vacuum hose into the suction port.
If you vacuumed on waste, you will need to turn your filter to the “rinse” setting, turn on the pump and let it run for about 30 seconds, and then turn the pump back off. Make sure to set your filter back to “filter” after you do this.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
Wait for a few minutes until the water runs clear. Turn off the pump to cease the backwashing. Turn the filter valve handle to RINSE and ensure the handle locks in place. Allow the rinse process to occur for 1 minute or until the water is clear.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear.
Chemicals that you add to your pool while the water is circulating don't need to be recirculated; they will stay mixed even if you don't pump the water continually. Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time.