Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
Now is the time to add Pool Clarifier and let it circulate for 12 hours. This will clump the algae together into vaccumable pieces. Shut your pump off and let the cloudiness settle. This may take up to a few days for very cloudy pools.
In a pool where algae is present, algaecides work in conjunction with chlorine to kill the algae cells. The algaecide causes the cells of the algae to burst, which destroys the plant. Different algaecides are used for different types of algae.
You can add 200mL every week to prevent algae from growing in your swimming pool. Also, algaecides tend to include metal bases, and you don't want to add too many metals to your swimming pool. Metals in your water can cause staining.
Algaecides treat and prevent pool algae, but not all algaecides are created equal. To treat green pool water, ensure you select an algaecide that kills green pool algae. After treatment, some dead algae may remain in your pool. Continue to thoroughly brush your pool's surfaces often.
The algaecide in the kit can cause some foam if there is no algae in the pool to destroy – it lingers around with nothing to kill. Spring time algaecides use surfactants to work and these molecules can react with agitation to cause froth.
Chlorine—yep, your typical sanitizer—is much more effective at killing algae than algaecide is. Even if your water gets cloudy and your walls get slimy, chlorine can still kill it. That's because chlorine oxidizes bacteria and single-celled algae, which means they trade electrons.
Algaecides. While algaecides are pretty shelf-stable and will be viable for up to five years, we only recommend getting enough to cover you for a season and a little bit for the off season.
Use a pool brush to vigorously scrub any pool surfaces covered in algae, including the walls, floors, and steps. Apply a green algaecide according to the directions on the label. Let the water circulate for 24 hours, then brush the pool surfaces again. Vacuum or backwash to remove any remaining dead algae.
Results in 24 Hours
Non-foaming formula works fast to kill pool algae.
If the pH or alkalinity of your pool is off, that may be the culprit. Debris, phosphates, and pollen also can cause yellow algae, and you're more likely to get algae in warmer climates or in areas with environmental and atmospheric changes.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Baking Soda and Green, Blue, or Yellow Algae
You'll need to use an algaecide to kill the algae and superchlorinate your pool to clear the water. After this treatment, test your pH and alkalinity and add baking soda to raise alkalinity to at least 100 ppm and pH to between 7.2 and 7.8.
Add pool algaecide at a rate of 12 ounces per 5,000 gallons of pool water.
Registered algaecides include copper sulfate, copper chelates (ethanolamines, ethylene diamines, triethanolamines, triethanolamine + ethylene diamine, and copper citrate/gluconate), endothall (as the mono (N,N-dimethylalkylamine) salt), and formulations containing the active ingredient sodium carbonate peroxyhydrate.
Swimming pool foam can be a huge distraction in and outside of your pool. Foam, or bubbles, make the water feel sticky and can make swimming uncomfortable for some. Good news for the kids, though, a foamy pool is safe to swim in. Still, we always recommend getting rid of the foam as soon as possible.
High Bather Load
On top of that, skin oils, sweat, (and urine) also build up with lots of pool guests. This is a good recipe for foam buildup, especially if you don't test and treat your water soon after your party leaves. Untreated water after a high bather load often results in foam and cloudy water.
Air bubbles in your pool mean that air is being sucked into the line on the suction side of the pump. It's likely happening because of one of these issues: The pool water level is too low. The strainer pot lid isn't on tight or its O-ring is loose/absent/compromised.