Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Typically, you should backwash a pool if the pressure gauge on your filter is at 8-10PSI at the starting level. So, to answer the question of how often should you backwash your pool, check your PSI. If the filter runs well at 16PSI and then goes up to 25PSI, your pool needs a backwash.
How Often Should I Backwash? A good rule of thumb is to backwash once the pressure displayed on your pressure gauge is 8-10 psi over the starting level. Backwashing after heavy rains, treating for algae, or when trying to clear cloudy water will keep your filter working efficiently.
Set the sand filter valve handle to the BACKWASH pool position and ensure the handle locks in place. Turn on the pump and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear. Turn Off the Pump.
When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.
Whenever the filter fills up with the dirt/debris it reduces the flow of water to your pool. Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
A pool needs a clean filter and it needs to be cleaned periodically-usually once a month in swim season and perhaps less frequently in the offseason. If your pool's filter is oversized by design, these filters need cleaning 3-4 times per year by a pool professional.
On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter's pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.
Run your filter 24 hours a day and backwash 3 or 4 times a day for quickest results. Green or cloudy water will quickly clog a filter, therefore you may have to backwash your filter many times a day until the pool clears. THIS IS NORMAL ! Remember, you cannot over-backwash a pool filter.
Backwashing a filter too frequently will keep the sand so free of dirt buildup that it will not have the ability to remove the smaller particles of dirt and they will simply pass through sometimes causing cloudiness in water.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
DE Blow-Back: If DE powder is coming into the pool, you may have torn filter grid fabric. Or, you could have a cracked top manifold, or missing air bleeder. The standpipe o-ring could be missing, or the filter valve could be allowing some DE powder to bypass the filter as you add it new.
Grids usually last a long time, up to about 10 years unless they are subjected to extreme conditions for extended periods.
You should clean your DE filter at least once every month or whenever you're pounds per square inch is 8 to 10 pounds above the normal starting pressure. Cleaning your DE Filter involves three basic steps: Backwashing, Cleaning the manifold and grid and adding new DE. The first step in cleaning your DE is to backwash.
Set the valve to Rinse. Depress the valve selector handle, then turn it to the Rinse setting. After a backwash, sand and debris becomes unsettled settle in the filter's internal plumbing. The rinse setting returns to the normal path through the filter, flushing debris to waste.
After a backwash, to get the amount of DE powder, simply take the recommended amount of DE powder for a new filter and multiply it by 0.8, or 80%.
Backwashing is a process that is used in water and wastewater treatment to pump water backward through filter media, which includes anything placed in a filter that changes the quality of water flowing through it.