How often should I have to fill my pool? This will vary depending upon several factors including: weather, if the pool is covered or not, bather load, and if it is heated or not. With pools that are covered, a good rule of thumb is that they should not have to be refilled more often than once every 2 weeks.
Normally pools see ¼ – ½ inch loss of water per day due to evaporation. This is roughly 2 – 4 inches per week. For a normal sized pool you will loose 25,000 to 50,000 gallons of water per year due to evaporation. This means I was putting a hose in the pool every 7-10 days to fill the pool.
If pool owners or maintenance workers are constantly filling up the pool, there may be a leak. On average, swimming pools lose about a quarter of an inch of water each day, yet variations in wind intensity, humidity and sunlight can drastically change water loss rates.
You can do the “bucket test” on your pool to measure evaporation. Place a bucket of water beside the pool and mark both the water in the bucket and the pool water level. Wait 24 hours then check the loss of both. If the pool loses more water than the bucket, then you have a leak.
You should aim to have your water sitting at the halfway point of your skimmer hatch (which sits on the side of your pool). It is recommended you have your water level between one-third and one-half up the swimming pool skimmer box opening.
Shock is liquid or granular chlorine. You should add one gallon (or one pound) of shock per 10,000 gallons of pool water every week to two weeks. During hot weather or frequent use, you may need to shock more frequently.
I think the answer to your question is about 3-6 days. The problem is that the chlorine that you need to keep the bacteria in check is used up more quickly as the temperature rises, the activity increases, and as sweat and other body stuff is put into the pool.
But did you know there's an easy way to reuse the water that's already in the pool? All you have to do is recycle it! Meet reverse osmosis — the best way to purify your swimming pool water. It works by pushing the existing water through semipermeable membranes that hold off any impurities, particles, and buildup.
Swimming Pool Water Harms Plants
Swimming pool water contains chemicals, especially chlorine, that can harm your trees and landscape plants when water drains and floods the area. Too much chlorine can damage tree leaves and other delicate tissues. Too much chlorinated water all at once can even kill trees.
Flooding Your Grass Is Not A Good Idea
The problem with draining your pool in the yard, if permitted by your local water regulatory laws, is that it will quickly reach its saturation level and increase the risk of flooding your lawn, drowning the roots of your grass, and attracting mosquitoes.
Chlorinated water, such as that from a pool is not suitable for watering plants. High levels of chlorine are toxic to plants.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.
The Bottom Line about Pools and Chlorine
As mentioned above, you could probably swim in a pool without chlorine without any major health issues. However, long-term use of a pool lacking chlorinated H2O could make you sick or, at the very least, contribute to rashes and other types of skin irritation.
Aim to maintain a chlorine level of 3 to 5mg/l at all times. How frequently you add more chlorine will depend on your usage and bathing habits. It could be daily, every two to three days or weekly. For 1mg/l, add 2g per 1000 litres.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
Sun Down – You'll want to shock your pool in the evening when the sun has gone down. This gives your pool plenty of time during the night to free the chlorine and clean the water. In the morning, you should be able to enjoy your pool. If you shock your pool during the day, the sun's UV rays will dissolve the chlorine.
It is important to know what exactly bleach is before you put it in your pool. Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine.
Salt cells convert salt into active chlorine for a lower cost as compared to the traditional form of liquid or solid chlorine. Salt water pools reduce skin and eye irritation and greatly reduce the chlorine smell.
Before getting in
Don't swim or let others swim if sick with diarrhea. Shower for at least 1 minute before you get into the water to remove dirt or anything else on your body.
Alkalinity Adjusting Chemicals for Pool Start Up
This should be the first chemical that you add to your pool during start-up. This one can really affect the pH level of your pool. Sorting this out first prevents you from ruining your hard work on your pool's pH level by doing it afterward.
BUT, if you have to shock your pool during the day in broad daylight, you can still swim after adding shock. It's recommended that you wait one hour after adding shock with the filter running, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
A: It's a waste, but fresh pool water is not safe for irrigating plants. It's because the chlorine in pool water is very toxic to plants. If the chlorine level is low enough, it's possible to use it.
A: Other salt water pool owners report being able to use the water on garden plants with no harm. According to one source, salt water pools have a salt content between 2500 and 4000 parts per million.