The average system uses approximately 15-16 gallons per minute, per station. Here is an easy formula to help you calculate the approximate amount of water you are using each month.
Normally each sprinkler head can deliver anywhere from I to 6 gallons per minute. A typical residential water meter can deliver 30 gallons per minute. With this in mind; 5 sprinkler heads can use 30 gal/min.
Watering with a typical sprinkler using a standard 5/8" garden hose for one hour uses about 1,020 gallons of water; if you water three times per week, that's about 12,240 gallons per month.
To determine how long you need to water to get one inch, place a plastic container in your yard and set a timer. On average, it will take 30 minutes to get a half inch of water. So, 20 minutes, three times per week will give a lawn about an inch of water. This formula works best with healthy, well-cultivated soil.
Water Thoroughly: Rotor zones should run for about 30-40 minutes per zone and spray zones 10-15 minutes per zone. 2. Water Frequently : Sod areas should be watered at least 2 or 3 times daily for the first two weeks.
If your sprinkler output is 1½ inches per week, your sprinklers should run for only ⅓ hour or 20 minutes that week (½ divided by 1½). On a twice-weekly watering schedule, run your sprinklers 10 minutes each time.
Watering every day is not advised. It should be done 2 to 3 times per week only to prevent a shallow root system. If possible, water during the early morning hours to ensure that the lawn dries entirely before nightfall. However, watering at any time of the day is better than not watering at all.
For conventional sprayheads, precipitation rates typically range from 1.3 inches to 2 inches per hour. For gear drive rotors, precipitation rates typically range from 0.4 inch to 1 inch per hour. For rotary nozzles, precipitation rates typically range from 0.4 inch to 0.6 inch per hour.
The average system uses approximately 15-16 gallons per minute, per station.
Sprinklers generally cover up wider ground and spread out water at a slow yet steady pace, which makes all the soil moisturized evenly and soaked underground. A watering hose takes time to cover space and can clutter the soil if there's too much water.
The average usage of water in a residential sprinkler system is between 12 – 30 gallons per minute depending on the type and size of the sprinkler head.
A general rule of thumb, especially in the summertime when the temperatures are high, is to always set your watering times for the early hours of the morning. At Commercial Lawn Irrigation, we recommend sprinkler system run times be set between the hours of 4:00 and 6:00 in the morning.
NFPA 13D Chapter 10 requires hydraulic calculations flowing a maximum of 2 sprinklers — 26 gpm total for standard residential sprinklers. Q = flow (gpm) C = friction loss coefficient (150 for plastic pipe) d = actual internal diameter of pipe (in.)
To calculate the amount of water you use, multiply the width times the length of your yard in feet to get the number of square feet of area. Then multiply that figure by 0.623 to come up with the number of gallons used (or use our calculator below).
Nothing should be in that area between the bottom of the sprinkler heads and the imaginary horizontal plane parallel to the ceiling that is 18 inches below. This is done to allow an even and unobstructed spray pattern from the sprinklers when triggered to extinguish the fire.
A common rule that is followed for obstructions within 18 inches of the sprinkler deflector is the “three times rule”. This requires sprinklers to be positioned away from obstructions a minimum or three times the maximum dimension of the obstruction.
Avoid watering grass on a hot afternoon when it's 95 degrees or higher. The best time to water grass is at dawn or in the early evening. Water deeply three times a week instead of a little water daily. Test whether your sprinkler system is watering your lawn evenly.
Water Wisely
Most lawns need to be watered no more than three days a week in the spring as well as in the summer and two days a week in the fall. This watering schedule is recommended under normal water supply conditions.
You should run your sprinkler system for as long as it takes to apply a half inch of water to your lawn. You will need to water for at least 10 minutes per week for most systems. Measure your sprinkler system's output to ensure you're not using too much water or underwatering.
At different pressures, the sprinkler head and nozzle will consume different amounts of water. For example, at 35 pounds per square inch (PSI) the 5000 Series Rotor using the 3.0 nozzle will use 3.11 gallons per minute (GPM). If your home's water capacity was 10 GPM, you could place 3 heads per zone.