Average R407C prices range between $5 and $7 per pound.
Refrigerant can only be sold to technicians who have a license from the relevant state or federal government.
The best replacement for R-22 Freon is usually R-407c. It has a very low loss in capacity (0 – 5%) relative to R-22 and is less expensive than many other R-22 replacement refrigerants. If a system has R22 in it already you cannot use a replacement refrigerant to simply add to the R22.
R-410A refrigerant costs an average of $40 to $75 per pound. This cost will continue to rise over the next several years since the supply will be reduced significantly due to the EPA phase-out.
It is essential to ensure enough refrigerant in your air conditioner, as too little can cause the system to work less efficiently, and too much can be dangerous. The general guideline used when calculating the amount of Freon in a residential A/C unit is 2-4 pounds per ton of cooling.
Average R407C prices range between $5 and $7 per pound.
The commonly used synthetic refrigerants such as R134a, R407C and R410A have a GWP value higher than 2,500. As a result, their production is being phased out.
Using these retrofit guidelines, many R-22 systems can be retrofitted for use with Freon™ 407C in air conditioning, heat pump applications, and refrigeration applications to allow existing equipment to continue to operate safely and efficiently, even after R-22 is no longer available.
Opteon™ XP20 (R-449C) refrigerant is a hydrofluoroolefin (HFO) option that replaces R-22 and R-407C in residential and commercial air conditioners, as well as direct expansion chillers. It has similar performance and properties to R-22 and R-407C and can be used in both retrofit and new equipment.
An AC leak will lead to warmer air from your vents over time. In most cases this can be fixed with a proven stop leak additive to seal up any leaks. When it's time for an AC recharge, turn to AutoZone.
Refrigerant can only be sold to technicians certified under the Section 608 or Section 609 technician certification programs, where individuals may only purchase refrigerant consistent with the appliances covered by their certification.
Heating mode The compressor pressure ratio of R-407C was 0.7% to 9.3% higher than R-22 for the two heating mode test conditions.
Yes. With air-conditioning systems that are similarly optimized, R134a is more energy-efficient than R407C. This fact is explained by the below graph and is demonstrated by the calculation of both cycles using the data and tools published by the leading refrigerant manufacturer – DuPont.
Factors Influencing R-410A Refrigerant Prices
Supply and Demand: As the phase-out progresses, the supply of R-410A will diminish, causing prices to increase due to scarcity. Regulatory Changes: As the phase-out continues to restrict production levels and importation, the R-410A price will likely increase.
New Regulations Effective from 2025
This includes refrigerants like R410A and R407C, which will no longer be permitted in such systems.
R407C is suitable for residential & light air conditioning and direct expansion air conditioning systems. It was chosen to replace R22 by many new equipment manufacturers and is also used in medium temperature refrigeration systems.
R22 (also known as HCFC-22) is a chlorofluorocarbon (CFC) once widely used as a refrigerant. If your home or office AC is over 10 years old, it's probably using R22 freon. However, R22 Freon is banned in the U.S. today.
A number of common refrigerants, including R134a, R410A and R407C, will be banned from use in new chillers in the USA from January 1, 2024.
Replacing R-22 with Freon™ 407C in these systems requires switching to polyolester (POE) oil. For a no-oil change R-22 replacement, see Freon™ MO99.
Due to the zeotropic nature of R-407C, it should be charged as a liquid to prevent fractionation (changes in refrigerant composition due to vapor charging.
Tradewater is the only climate-focused refrigerant buyback program in the world. Get paid to fight climate change by selling your old refrigerants, like Freon, to our EPA-certified technicians.
According to PG&E, most central air conditioning systems use two to four pounds of refrigerant per ton of cooling capacity. A three-ton air conditioner would typically have six to 12 pounds of refrigerant for a proper charge.
Under EPA regulations, only a certified professional can recharge your home's HVAC system.