Water pressure regulator replacement: $250 to $1,000. Pipe section replacement: $500 to $4,000.
Typically, water pressure regulators cost about $50 to $100 on average1, though you could end up paying up to $2001 depending on the size of incoming water line.
A quick and easy way to increase water pressure is to adjust the pressure-reducing valve, which can be found in your home, usually close to your water meter. If your pressure gauge reading was low, make slight adjustments to your regulator.
A quick and easy way to increase water pressure (for homes supplied by a municipal water system) is to adjust the pressure-reducing valve, which can be found on the main water-supply pipe; look for a conical-shaped valve next to the water meter, close to where the main water pipe enters the house.
However, when low water pressure originates from an issue specific to your home, such as a water pipe or your pressure regulator fails, plumbing repairs can correct the problem.
The good news is that you can easily replace faucet aerators, clean showerheads to remove limescale, or simply buy new fixtures to replace the defective ones, which can improve your water pressure. However, it is important to know that repairing or replacing faucets and fixtures is only a temporary solution.
Partially Closed Valve
One of the most common issues that can lead to low water pressure problems is that the water is being obstructed by one or more partially closed shutoff valves. Typically, a home will have one main shutoff valve located inside the house.
Expensive Water Bills: If your water bills seem a lot higher than expected, you're using more water than usual. This can be a sign that your pressure is too high.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
Water Pressure Readings
Normal water pressure is generally between 40 and 60 PSI. Most homeowners prefer something right in the middle around 50 PSI. Once you measure the water pressure in your house, you can adjust it to a setting that is ideal for all family members and household uses.
The primary way to fix high water pressure is by installing a water pressure regulator. If you already have one, you will need to adjust it or replace it.
If I install a Water Pressure Reducing Valve, what savings can I expect? An average savings would be from $50 to $150 per year, probably much higher. Based on the fact that 1/3 less water flows at 50 lbs. than 100 lbs., you can expect to save up to 1/3 of the water previously consumed.
It may be caused by debris such as dirt, sand, solidified oil and grease, food particles, or foreign objects. Pollutants can block pipes if they back up due to fractures in the water main. Mineral buildup clogs pipes over time and causes the water pressure to go down, as there's less space for water to travel through.
(Normal is 60 psi and very few areas are below 40 psi) The pressure of the streams will drop under these extreme conditions, of course, but the stream integrity is preserved. This photo shows the stream integrity of our Perfect shower head (old style).
Most residential plumbing systems are designed to handle 40 to 60 PSI of pressure, with 80 PSI being the typical maximum and anything over 100 PSI being possibly detrimental to plumbing components.
Pressures above 80 psi are too high. Whereas low water pressure is more of a nuisance than a serious problem (some fixtures, like washing machines, have minimum pressure requirements), high water pressure carries with it a significantly increased risk of damage to pipes, joints, fixtures and seals.
Many toilets really do leak only at night; that's because people use much less water during these hours and in many municipal water systems, the water pressure rises considerably during this time.
Water companies should make sure that high water pressure does not cause damage to a customer's property if the customer's fittings meet normal standards. If you have a problem with water pressure, speak to your water company first.
A water pressure regulator, if you have one, is usually located where the main water line comes into the house and after the main shut off valve. This way if you need to work on or change the water pressure regulator you can simply shut off the water main to do so.
If there's an accumulation of sediments in your hot water tank, it can lower your water pressure. The presence of kinks in the flexible water pipes used in water heaters can result in low water pressure. If the shut-off valve isn't fully open, water pressure can drop.
Low water pressure in the home is usually the result of clogged pipes or simultaneous use of two or more plumbing fixtures like kitchen sink, toilet, hose, or shower.