Cost of labor. A plumber may charge as little as $40 hourly. Or, they may charge more than $150. Repairing a heater usually takes two hours or less.
If so, you're probably wondering how much a maintenance visit will cost you. The cost of water heater maintenance ranges from $75 to $300+, depending on the following factors: What the plumber checks during a maintenance visit. Whether you choose a single visit or an annual maintenance plan.
In general, plumbers cost $45 to $200 per hour, while electricians cost $50 to $100 per hour. Expect the following average price ranges for labor alone: Replacing a tank-style water heater: $150–$450.
Inspect your water heater.
The plumber will perform a comprehensive inspection of the connections, pressure relief valves, and other fittings for the water heater.
The short answer is that plumbers typically service water heaters, whether it's gas or electric. An electrician may also be able to fix an electric hot water heater, assuming the problem is electrical. Maybe you're wondering if you can DIY the solution or if you need to call a water heater pro.
But for the most part, you should call a licensed plumber for all hot water heater problems.
If so, it's best to call a plumber for water heater repair. This is because there could be a gas leak. Gas leaks are extremely dangerous and should be fixed as soon as possible. Call a plumber right away if you smell gas.
It is mandatory to keep a regular maintenance schedule.
This can possibly be every two months, once in every six year and once in every year. The first check should center around observing the plumbing joints for excessive or unusual corrosion. This check applies to only gas powered heaters.
Most standard plumbing inspections will take around two hours to fully check all plumbing and appliances in a home. This of course depends on the size of your home, additional inspection services needed, and overall access to your plumbing.
Sediment buildup inside the heater's tank not only clogs your water lines, but it can impact the heater's energy efficiency. Flushing the heater can prevent buildup and protect the appliance. Ideally, you'll want to call a licensed plumber to perform this task.
A furnace inspection costs an average of $80 to $100. Your cost may increase if more furnace repairs are needed, or based on the specifics of your HVAC system. If detrimental issues are uncovered, you'll be quoted for the repair or potential replacement of your HVAC equipment.
The national average cost to flush a water heater is $160, but prices can vary in increments based on the tank size. A 30-gallon tank will cost between $90 and $120 on average, while a 70-gallon tank could cost anywhere between $180 and $250.
While today's water heaters are better designed than older models, they still require regular maintenance in order to prolong their lives. With regular inspection, draining, and flushing, you can expect a gas water heater to last anywhere from 8-12 years and an electric water heater to last anywhere from 10-15 years.
The average cost of a plumbing inspection is $100 to $200 for a basic visual inspection, $300 to $1,100 for a camera or video inspection, or $400 to $1,300 for a combination of the two. Plumbing inspections typically cover fixtures, water and sewer lines, water heaters, toilets, pumps, drains, and appliances.
Flush your water heater every six months or so. If you have harder water, or water that contains more minerals, you may want to flush it more often.
Verify no voltage with volt meter. Disconnect two wires from top element. Check continuity of element with ohm meter from terminal to terminal (should read around 13 ohms). Check continuity from each terminal to metal tank (should read 0 ohms - anything else and the element needs to be replaced).
Usually, you'll get a report within three or four days. At this point, the buyer can request that the homeowner make repairs or hire contractors to do the work before closing. Some repairs are required to be made, especially if the inspection report finds code violations or problems with water seeping into the home.
Every pipe and fitting will be inspected thoroughly and checked for damage, cracks, and leaks. Sink and tub faucets, showerheads, sink plumbing, and drains will be checked for leaks or slow drainage. Outdoor hose bibs should also be inspected for leaks, fitting conditions, and proper freeze and frost protection.
You can flush your water heater yourself if it's done on a regular basis. This guide will take you through the steps to drain and flush a gas or electric water heater. Learning how to clean a water heater is an essential part of maintaining your plumbing system.
Water heater - The plumber will inspect the water heater installation, flue pipes, safety valves, energy efficiency, leaks, corrosion and signs of rust/damage. Gas lines - If you have natural gas service, the plumber will check gas pipes for leaks using a sniffer device. All connections are inspected for safety.
Where You Live. The cost of parts and labor varies by geographical location. For example, the average cost of water heater repairs in Tampa, FL, is $539. But in Los Angeles, CA, and Houston, TX, expect to pay up to $627.
Expect a pro to charge you between $75 and $200 to come to your home to flush your water heater, depending on where you live. While this cost deters many homeowners from performing this annual maintenance, it can extend the water heater's lifespan by years, making it worth the additional cost.
Water heaters are actually part of your plumbing system, not your HVAC system, because their purpose begins and ends with the temperature of the water supplying your faucets, showers, dishwasher, and washing machine.
The Home Depot partners with local, licensed and insured professionals to help homeowners choose the right water heater for their home. If you live within 30 miles of a Home Depot store and call us before noon at 1-800-HOME-DEPOT, our team offers same-day installation.