Wait about 10-15 minutes before trying to unclog the toilet, as some water might drain on its own.
When a toilet has a clog made of water-soluble materials, it has a chance of slowly dissolving in the water and freeing up the toilet to work properly again. So, clogs that are primarily made of toilet paper can clear themselves.
You may just be using it incorrectly. Do this: Next time you have a clog, use your plunger like this: Ensure the flange lip is unfolded. Get a good seal on the toilet drain (that is, make sure you're covering the entire drain or you won't have enough pressure to loosen the clog.)
Using a plunger is one of the most effective methods used for unblocking a toilet as it can unclog a wide variety of waste pipes.
Soap and Hot Water - Remove some of the water in the toilet with a cup or bowl to make room for adding about a gallon of water. Put a soap dish, shampoo, or slivers of bar soap in the bowl. Then heat a gallon of water to the temperature of hot tea, pour into the bowl, and wait about 20 minutes.
Attempting to force a clog through a toilet with a plunger can often make the problem worse. Instead, create a seal and slowly push down on the plunger before pulling it back sharply. The suction can help pull the clog back up toward the bowl, breaking the blockage and allowing gravity to take over.
The answer might surprise you: dish soap. Yes, that's right. Dish soap can be your savior when it comes to unclogging toilets quickly and efficiently. Simply pour some dish soap into the clogged toilet bowl and let it sit for about 10-15 minutes.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
A fully clogged toilet won't move waste down the drain at all. If it's running slowly, it's a partial clog that does let water through, but not as fast as it's supposed to be.
You can use Drano® Clog Removers to unclog a kitchen sink, bathroom sink, shower or clogged bathtub, but DO NOT use them in toilets. For clogged or slow-running drains, apply the product and let it work 15 minutes, then flush with hot water. For tough problems, allow 30 minutes before flushing.
It can hurt the toilet and soften/dissolve pipes— Drano uses caustic or oxidizing chemicals to create heat to unclog a drain. If Drano does not clear the toilet, this heat can crack the porcelain, soften PVC pipes and dissolve old, corroded pipes.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
Drano® Liquid Drain Cleaner starts working to unclog your drain on contact. After 15 to 30 minutes, clogs are substantially minimized or dissolved. A final blast of hot water flushes away what's left of the clog.
Bleach is an effective way to deal with blocked toilet drains as it is a dilute solution of sodium hypochlorite and also contains a high chlorine concentration. Using bleach by itself or mixing it with boiling water are effective ways to unclog a toilet.
Using a snake is also more invasive and time-consuming than using a chemical cleaner is, and can often become a dirty job. When it comes to getting at and removing major clogs or clogs that are deep down in your pipes, however, a plumber's snake is your best bet.
It is Extremely Corrosive For Your Drains
When your pipes are clogged, Drano will sit on top of the clog, continually reacting and generating heat until the clog dissolves. This can put a great deal of stress on your drains as the heat can cause PVC pipes to soften and even break or collapse.
The most common causes for a slow-draining toilet are: A clog in the drain line. A blockage between the tank and bowl. Poor or Clogged Venting.
The main reason you're seeing bubbling water in your toilet bowl is from a lack of airflow in your sewer line through a vent pipe.
Check water level in toilet bowl
Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
High Water Pressure with Baking Soda and Vinegar
To do this, use a 2:1 ratio of vinegar to baking soda, and mix it into 60 gallons of water. As you pour the water down the drain, use a drain snake or plunger to dislodge debris that is blocking water flow.