After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
When you backwash a pool, you send water backward through the filter, and out the waste or drain port. This forces all the debris caught in the filter to dislodge so you can easily remove it and restore the filter's normal functioning level. Think of it like using a strainer in your kitchen sink.
When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value's waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.
* Can i discharge the backwash water onto my lawn, will it harm the grass / plants? The DE doesn't harm the grass or plants, excessive chlorine or saltwater may.
It is not recommended to drain a swimming pool through the backwash valve. While sucking from the main drain and putting the water down the backwash line will work in some scenarios it puts your pool pump at risk of losing prime and running dry.
Open-air bleeder assembly on the filter, and turn pump on. Watch pressure gauge for back pressure (over 30 PSI) and hose for kinks. Be prepared to shut off the pump quickly if the pressure gauge spikes. After the hose fills with water, backwash your sand filter for 2 – 3 minutes or until water runs clear.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool's size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool's turnover rate is.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
In unsewered regions, backwash water is to be discharged to a grassed, vegetated or garden area, or a stone-filled trench either open to the surface or underground (similar to a septic tank absorption field).
Your pump may be too large or the sand level too high in the filter. When the filter is backwashing the water flow can cause the sand to rise high enough and overflow into the standpipe, which will allow the sand back into the pool.
Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
If you see it blowing out into the pool, something is broken. The most common problem is a cracked lateral, which is one of the perforated pipes at the bottom of the filter that catches water that has circulated through the sand.
Typically, you should backwash a pool if the pressure gauge on your filter is at 8-10PSI at the starting level. So, to answer the question of how often should you backwash your pool, check your PSI. If the filter runs well at 16PSI and then goes up to 25PSI, your pool needs a backwash.
After a backwash, to get the amount of DE powder, simply take the recommended amount of DE powder for a new filter and multiply it by 0.8, or 80%.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
For inground pools with a sand or DE filter, the easiest way to quickly lower the water level is to place the multiport valve into the waste position and roll out the backwash hose. If instead, you have a slide (push-valve), backwash the filter to lower the water level.