Run your pump overnight, or if possible, for 24 hours to clean all the debris from your pool water.
Pour the algaecide dose into the water, depositing it in several areas around the pool. Your swimming pool pump should be running at this time to help circulate the algaecide. Wait about 30 minutes before allowing anyone to swim after the algaecide application.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
We recommend waiting at least 15 minutes to swim after adding algaecide to your swimming pool.
Let the water circulate for at least two hours.
Circulate the water for about 2 hours to ensure the flocculant is fully mixed in, then shut off your pump and let it sit overnight. During this time, the chemical will start to bind the particles together and settle them to the bottom of the pool.
Now is the time to add Pool Clarifier and let it circulate for 12 hours. This will clump the algae together into vaccumable pieces. Shut your pump off and let the cloudiness settle. This may take up to a few days for very cloudy pools.
So unless you're dealing with mustard algae or black algae, leave the algaecide on the shelf and get ready to shock the heck out of your pool. But when dealing with regular ol' green pool algae, chlorine is your best bet to kill it dead.
Cyanuric acid levels should be from 10 to 40 ppm to prevent the chlorine you add from quickly degrading. Because it's sunlight that degrades chlorine, the best time to shock is in the late afternoon so the chlorine has all night to work.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
In a pool where algae is present, algaecides work in conjunction with chlorine to kill the algae cells. The algaecide causes the cells of the algae to burst, which destroys the plant. Different algaecides are used for different types of algae.
Add Algaecide After Shocking
Wait for the pH to fall to a safe level for swimming (3 ppm or below) and then add a product such as Pool Time Algicide + Clarifier in the amount recommended in the product instructions. Pour this incrementally into the water as you walk around the pool.
When closing and winterizing your pool, it is important to remember to balance your pool water's chemistry prior to closing and don't forget the algaecide. Algaecide is simple and effective with one quart of winter algaecide typically enough to treat 20,000 gallons of water all winter long.
Too much algaecide can cause foaming that can damage your filter. In some cases, too much algaecide can also cause eye and skin irritation. In addition to adding algaecide after shocking your pool, you should add algaecide to your pool water when closing down for the year.
Algaecides treat and prevent pool algae, but not all algaecides are created equal. To treat green pool water, ensure you select an algaecide that kills green pool algae. After treatment, some dead algae may remain in your pool. Continue to thoroughly brush your pool's surfaces often.
How long will it take to clear the pool? A fiberglass pool in its worst condition can be algae-free in 24 hours. For a vinyl liner pool, the process can take 3-4 days. For a concrete pool, this can take a week or more.
The algaecide in the kit can cause some foam if there is no algae in the pool to destroy – it lingers around with nothing to kill. Spring time algaecides use surfactants to work and these molecules can react with agitation to cause froth.
TEST IN THE MORNING
If you are having chlorine issues in your pool, the best time to get a water sample is in the morning. Even with proper amounts of chlorine stabilizer, chlorine will burn-off during the day. Testing in the morning will give your water a chance to circulate all night and avoid the sun's UV rays.
Algaecide is a chemical substance that biologically controls the growth of algae. It can be used in pools, fountains, and ponds.
After treating one section, you can wait 7-10 days for the water to re-balance and determine if a second treatment is required. If it is, treat the second section and repeat the process until algae is under control.