Dry time depends upon thickness of the application. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears. Unicorn SPiT dries quickly. Use a spray bottle of water to keep product from drying out and to easily manipulate.
UNiCORN SPiT® dries quickly. Dry time is approximately 3 minutes to 48 hours depending on material, technique, humidity and temperature. A dull chalky finish will appear letting you know when it's dry.
UNiCORN SPiT BLOG
Multiple coats of gloss topcoat or one coat of epoxy / resin like FAMOWOOD GLAZE COAT will result in a unique, deep three dimensional effect. SEALING: While sealing is not mandatory, we advise sealing for durability and moisture protection. Multiple coats are recommended for extreme durability.
Allow stain to dry approximately 6 to 8 hours.To darken the color, apply additional coats by following the instructions above. Let the stain dry 6 to 8 hours between coats.
Unicorn SPiT dries quickly. Use a spray bottle of water to keep product from drying out and to easily manipulate. Once dry, use FAMOWOOD GLAZE COAT or other non-waterbased coatings to protect add gloss and dimension.
Use Unicorn SPiT right out of the bottle for a paint application or dilute it up to 10% with water for antiquing or dry brushing. Diluting Unicorn SPiT with water allows you to control the opaqueness. For antiquing or dry brushing, add 10 parts Unicorn SPiT in a re-sealable container to be diluted with water.
If your gel wood stain isn't drying completely, it may be due to several factors such as humidity, temperature, or application thickness. Try increasing airflow, adjusting environmental conditions, or lightly sanding the surface to promote drying.
Gel stain will be fine. Regular Minwax stains can cause finish problems down the road if left without wiping. Amount of stain left on the project is going to be the biggest factor. If you can still see through it and it dries with a day or so it will probably be OK.
There are two ways to tell if it is an oil-based product is dry. If it is no longer tacky and it doesn't smell, it is dry. You can tell if a water-based product is dry by touching it. If its cool to the touch, it's not dry.
Yes. Mix Unicorn SPiT colours together to create your own special colour OR mix most any water-based paint (chalk style or mineral based) with Unicorn SPiT to create custom colours.
Unicorn SPiT works on glass! Our concentrated gel can be used as a paint, stain, or glaze. Just add water or water based sealants or use in full concentration for these amazing techniques!
Unicorn SPiT is a water based gel stain and glaze paint. It can be waterproofed by applying a coating such as Epoxy Resin. Since it's water based it can't be mixed into resin, however once set, a coat of epoxy will add depth and brilliance to the colours while protecting the surface.
saliva will dry within an hour and forty minutes at room temperature and with the influence of various other factors saliva will dry in less than three hours (Jellinghaus et al 2015) .
THE BASICS OF HOW TO USE UNICORN SPIT
Pre-prep, lightly sand the wood you plan to use. The smoother the better.
If applied too thickly, they won't dry properly and will remain tacky to the touch. This can also happen if the wood wasn't stripped and sanded completely down to bare wood, since the stain will sit on the surface rather than soaking into the wood.
Applying the second coat too soon can result in peeling or uneven coloration, while waiting too long may hinder absorption. Manufacturer Guidelines: Most stains recommend waiting at least 4 hours between coats or until the first coat is completely dry.
Wipe the stain off immediately if you'd like a lighter tone. But for a deeper tone, leave the stain on the wood for 5 to 10 minutes before wiping it off. Be sure to wipe off all the excess stain going in the direction of the grain of the wood.
If the surface is still tacky or you can remove more than a faint trace of stain, the surface is not ready. If Gel Stain is tacky after 5 days, dry time requirements have not been met and it may never dry. The only alternative is to strip off the finish and start over.
Low to average humidity promotes faster drying. Also, be cautious of the direct sunlight – the stain will dry too fast before the wood is able to absorb it. The ideal temperature for staining a deck is between 50°F to 90°F.
Applying heat is one of the best ways to increase polyurethane drying times. For example, some individuals will use a hair-dryer, a space heater, or a heat lamp to turn up the heat on a polyurethane coat. Although these methods speed up dry time, they do not speed up curing time.
Unicorn SPiT is a paint, gel stain, and glaze concentrate all in one bottle! It creates a multifaceted, 3-dimensional effect on wood, glass, metal, fabric, pottery, wicker, concrete, laminate, and more. Fans love that it's nontoxic and comes in a variety of outrageous colors.
Unicorn SPiT dries quite quickly once applied. Use a spray bottle of water to keep it from drying out and allow it to be manipulated directly on the surface. Complete your design in one colour or add multiple colours to achieve your desired look. Allow your work to dry completely.
Direct to fabric projects: Mix Unicorn SPiT with 3-7 parts water in a spray bottle or cup and brush it on, drip it on or spray it on. Protecting your finished project: Use a NON-WATER BASED product intended for waterproofing fabric after Unicorn SPiT has completely dried.