Lastly, start slow and add force as needed. Several gentle pumps will usually work better than a couple of hard pushes. If your clog is going to come out, it should happen in less than 10 minutes. If not, it's time to move on to a snake or call a plumber.
Pump the plunger over the hole.
It may take 15 to 20 cycles before the toilet unclogs. Be patient. As long as you don't have a hard object (like a kid's toy) stuck in there, plunging alone often suffices. It might not work immediately but will often work after a few dozen plunge cycles.
When a toilet has a clog made of water-soluble materials, it has a chance of slowly dissolving in the water and freeing up the toilet to work properly again. So, clogs that are primarily made of toilet paper can clear themselves.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
We recommend you add a cup of baking soda to your blocked toilet and wait for some minutes. Next, pour two cups of vinegar slowly into the toilet. Vinegar and baking soda will typically react to form bubbles, so ensure you pour carefully and slowly to prevent the toilet water from overflowing or splashing.
So, let's recap the common reasons why a toilet won't unclog — excessive toilet paper use, non-flushable solids, hard water, and clogs in the main sewer line. Thankfully, they can be prevented via methods like double-flushing, covering the toilet bowl, routine inspections and dealing with tree roots.
Check water level in toilet bowl
After plunging for thirty seconds, quickly break the seal and remove the plunger. Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
Make your own drain cleaner by pouring one cup of baking soda and two cups of vinegar into the toilet and adding a half gallon of hot water. Dish soap can also help loosen some obstructions. When using either method, allow the solution to sit overnight and then flush the toilet to see if the obstruction has cleared.
Try Hot Water
The easiest and first thing to try when attempting to unclog toilets without a plunger is hot water. The addition of hot water might be enough to loosen the clog and dislodge the blockage. Fill a bucket with about a gallon of hot water from the sink or bathtub.
Bleach is an effective way to deal with blocked toilet drains as it is a dilute solution of sodium hypochlorite and also contains a high chlorine concentration. Using bleach by itself or mixing it with boiling water are effective ways to unclog a toilet.
For preventive drain cleaning, you can use Drano® Max Build-Up Remover in drains, toilets and even septic systems. Apply Drano® Max Build-Up Remover overnight or before you go to work, then wait 6 to 8 hours before running warm (not hot) water down treated drains or flushing treated toilets.
As it turns out, you can actually unclog a toilet with dish soap instead of turning to a harsh, toxic bowl cleaner. Just as natural dish soap helps break down dirt, grease, and food that may be stuck on dishes and utensils, it can help break down what's in your toilet bowl.
Coke or Pepsi are great for vanquishing a clog! Everyone's heard about how a nail will dissolve in a glass of coke over time, and although most of us know this is a stretch, coke is arguably better than many commercial chemical clog removers because of its strong dissolving agents!
Drano® Liquid Drain Cleaner starts working to unclog your drain on contact. After 15 to 30 minutes, clogs are substantially minimized or dissolved. A final blast of hot water flushes away what's left of the clog.
In this scenario, squeezing liquid hand soap, body wash, or shampoo into the toilet should net you the same results. STEP 2: Let the soap sit for about 20 minute so it can coat and loosen the clog for maximum flushability.
While you can use a regular drain snake in a toilet, a closet auger, or toilet auger, is a type of drain snake specifically designed for use in a toilet. Its unique design and protective rubber coating allow it to maneuver through the tight S-bend in a toilet without damaging the porcelain.
A Blockage Between the Tank and the Bowl
If there's lime buildup or other blockages in the inlet hole, then the water is seeping much slower than it should into the bowl. That means less pressure and a slower draining process. The best way to check for this problem is by watching the bowl when you flush.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.