Even though you've reset the AC at the breaker box, it doesn't mean it will start working immediately. Many systems need about 30 minutes to reset the internal circuitry before you can turn it back on at the thermostat.
Reset the AC Using the Isolation Switch
The isolation switch looks like an ordinary light switch with a knob. Once you locate it, turn the knob to the off position and leave it for at least 30 minutes up to an hour. This will allow the electrically operated components in the AC to reset.
Depending on the system, an optimal time of 3 minutes is required before switching the system on. If the system is turned on without waiting for at least 3 minutes, the system can start with a pressure load. This pressure load prevents the system from cooling properly, which could affect the system in the long run.
Some air conditioning systems have a reset switch, which is a small, red button. Typically, the button will be on the outdoor unit. If you have a problem locating it on the outdoor unit, you may find relevant details on the equipment's manufacturer's manual. Press the red button for three seconds and release.
Allow a 3-minute break after turning the AC on or off and reset the circuit breaker 24 hours prior to first use to prevent damage and improve efficiency. Perform a pre-start inspection by cleaning the unit, checking filters and coils, and starting the AC in fan mode before cooling to ensure it runs smoothly.
Wait 30 Minutes Before Restoring Power To The Thermostat
Wait for 30 minutes before turning your unit back on at the thermostat. Doing so gives your system a chance to reset its internal circuit breaker.
Installing a new air conditioner is exciting, but you must allow it to settle before turning it on. Although an air conditioner can be set in as little as 30 minutes, this is not always the case. The freon in an AC can settle in 22 minutes on average, but it can take up to 24 hours in some cases.
Why Do I Need to Reset My Air Conditioner? The most common reason to reset an AC unit is when the protection circuit breaker in your AC unit kicks in. In most cases, the protection circuit breaker is triggered during a power outage and is designed to prevent fires and explosions.
If your AC is running but not cooling, it could be due to a dirty air filter, incorrect thermostat settings, a malfunctioning thermostat, a refrigerant leak, dirty condenser coils, blocked vents or ducts, a faulty compressor, frozen evaporator coils, or electrical issues.
This is a short cycle protection. Something has happened, usually a power outage and this is a protection for your unit to not turn on and short cycle before all the pressures have been equalized. Wait 3-5 minutes for your air conditioner to be ready to turn on again.
Wear and Tear on the System
Turning your air conditioner completely off and then on forces the system to work harder. Each time the air conditioner starts, it experiences a surge of power, which can strain the components. Over time, this can lead to a breakdown or the need for premature repairs.
Once the AC completes a cycle of about 15 and 20 minutes, it should remain off for 7 to 10 minutes. This helps it cool off before starting another cycle. The stops happen 2 to three times per hour.
Check the thermostat
You should check if it's been set to the correct temperature and also make sure it's set to “cool”. If the AC settings are not right, it won't turn on. You can also check if the batteries in the thermostat are fresh and replace them if needed.
What Is Typical of Air Conditioners? Most of the time, the length of the cycle – from the period of turning off to turning back on – should be about 7 to 10 minutes. The system will often complete a full cycle every 15 to 20 minutes, then turn off for up to 10 minutes before turning back on.
In most cases, the small red reset button is inside the AC's compressor. If unsure, you can always refer to the user's manual to find the exact location.
Shut off your system by hitting the isolation switch, wait 30 to 60 minutes and then turn it back on. This manual reboot fully disconnects your AC unit from power, allowing all electrical components to reset.
There are a number of reasons why your air conditioner might be running but not cooling. It could be an issue with the thermostat, the compressor, or the evaporator coils. Or, it could simply be clogged with dust and debris, which is preventing it from working properly.
In general, wall and window air conditioning units with smaller capacities can typically run for up to eight hours at a time before they need to rest. Larger wall and window units have a longer running time of around 10 to 12 hours, depending on their cooling power.
If your AC unit has a reset button on the condenser unit, you simply press it and hope that the problem resolves. Look for it first around on the exterior of your machine, especially along the bottom edge near the ground. An AC's reset button is typically red and visible, so it should be easy to spot.
Resetting your thermostat is an easy first step in troubleshooting temperature control issues. If problems persist after a reset, you should contact an HVAC technician for additional diagnostics and repairs.
Freon settles in an air conditioner in a matter of minutes. Though, it depends on the type of air conditioner too. If the air conditioner is portable, it takes about 5-30 minutes for the Freon to settle. This time must be dedicated to the appliance for it to function properly.
Turning the fridge on too soon can lead to a coolant rush, which can cause problems like leaks or blockages. This can damage the fridge, and you may need to pay for expensive repairs. Waiting allows the coolant to settle back into its correct position and ensures that there are no leaks or blockages.
The answer is that Freon should last forever unless you have a leaking system. Contrary to popular belief, units shouldn't need to be recharged every year. Many customers call our office because their AC system isn't working as it should.