Most washing machines use a thermal lock that releases the door two minutes after a cycle is complete.
Unlock the Lid
Depending upon the speed at which the Washer is spinning when it is paused (and depending on the size of the load being washed), it can take as long as 3 minutes to coast to a stop and then unlock.
Usually, the door locks due to water not draining out completely. If you have a wet vac, suck all the water out from the drain hose in the standpipe behind the washing machine and it should unlock. If there is standing water, you likely have a clogged or faulty drain pump.
So the first thing you want to do is unplug the washer for 60 seconds and plug it back in to see if the latch will reset. If that doesn't work, listen closely and if you hear a motor running/humming--just leave the washer plugged in for 20 minutes and the washer should reset on it's own and unlock.
Most washing machines use a thermal lock that releases the door two minutes after a cycle is complete.
Sometimes, when using the machine, people accidentally hit the control lock or delay start button. Try opening and closing the washing machine door, and then try another cycle. If that doesn't work, you may want to completely restart and reset the wash cycle.
A: If your washing machine is showing a lock symbol, it likely means that the safety lock feature is activated.
Detach the drain hose from the back of your washing machine. Use a funnel to pour about a quarter of a cup of baking soda into the pipe. Next, empty a baster full of vinegar into the drain hose. Top tip: If the blockage is not completely gone, you can repeat the above process.
If the cycle has finished and the door is still locked, it may be due to a power outage or a fault in the machine's electrical system. In this case, try unplugging the machine and waiting for a few minutes before plugging it back in.
If the door or lid won't open at the end of the cycle, then the lock mechanism may be at fault. Most washers will have a manual release to unlock the mechanism and allow you to open the door or lid. The release is normally accessible from below the door lock, or on some models, from inside the soap dispenser housing.
Lock washers offer secure connections that can be removed or separated more easily than welded connections. To remove a lock washer, use a wrench or a similar tool to remove the nut or threaded fastener that holds the lock washer in place. Next, use a flathead screwdriver to pry the lock washer loose.
Washer Control Reset
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
If the door doesn't open as it should after the cycle has ended, the next step is to hold the “control lock” button down for 3 seconds. You should be able to hear an unlatching sound followed by being able to open the door.
Access the lid lock switch by unplugging your washer from the wall and turning off the water. Press a magnet against the lid lock mechanism for a quick, easy way to bypass the lid lock. Cut the 1st and 3rd wire (or 1st and 4th wire if there are 4 wires) that attach to the lid lock to permanently bypass it.
On front loaders it's so that the door is properly sealed when the machine engages and fills the drum with water so it doesn't end up all over the floor, and possibly into the electrics. Quick solution: Change the mode to "spin". That'll drain the water out of the drum.
Turn off the machine for 5-10 minutes and try opening it again: This method works in most cases when the door lock is stuck. Turning off the machine for a few minutes gives it time to reset and release the door lock. After a few minutes, try opening the door again.
Your washer door locks to prevent water from coming out (especially for front load models). Child Lock also will lock the door on some models, like front loaders. Normally waiting for the cycle to end is all you need to do to unlock the door, or turn your washer on if it's off.
Turn the washing machine off and unplug it.
Then, unplug the machine and wait 5-10 minutes. Try pulling the handle again to see if the door opens. Some locks automatically flip into the unlocked position after 5-10 minutes so that you can get your clothes during a power outage.
The most common cause is water left in the machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray). The door interlock has simply jammed.
There are three recommended methods of unblocking a washing machine drain yourself. These are to use baking soda and vinegar, a chemical drain cleaner, or do it manually. You can also potentially fix the issue by straightening out the washing machine drain hose if it has become twisted.
There are several reasons why a washing machine might not start. It could be due to a power issue, a faulty start switch, door lock problems, or even issues with the control panel.