So if you buy liquid shock, be aware that it only lasts one to two months at the most before it starts to lose effectiveness. While many swimming pool chemicals stay good for years if stored correctly, some pool-maintenance supplies expire more quickly.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
BUT, if you have to shock your pool during the day in broad daylight, you can still swim after adding shock. It's recommended that you wait one hour after adding shock with the filter running, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
Give the shock a good 12 to 24 hours to work it's magic. If the algae hasn't cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.
Best Time to Shock Your Pool
The best time of day to shock pool is when the sun is down. So, experts recommend shocking your pool in the evening or at night, to make sure it does its job. Shocking during the day can be ineffective as UV rays from direct sunlight significantly reduce free chlorine levels.
After you shock the pool — As soon as your chlorine levels reach 5 ppm or lower, it's officially safe to swim. Depending on the type of shock used, as well as the amount used, it can take anywhere from 24 hours or even up to a couple of days.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
It's recommended that you should do a pool shock once a week. The more you use the pool, the more often you need to shock it. Occasionally, you may need to perform an extra pool shock after: Heavy pool use, like a pool party.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
If your total chlorine level is high, you will use a non-chlorine shock; if it is low, you will use a chlorinated shock. As a rule, you will need to raise free chlorine to 10 times your combined chlorine to hit what is known as “break point.” Therefore, it is good to deal with combined chlorine while it is still small.
Never close the cover immediately after shocking the pool. It is recommended to wait several hours before closing the cover. Use a test kit to regularly test the pool water. If the tests results are good, this does not imply the water chemistry was good prior to your current test results.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
What happens if too much shock is added? You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
Chlorine, either solid or liquid, is a pesticide used in pools to destroy germs, including those from feces, urine, saliva and other substances. But excessive exposure to chlorine can cause sickness and injuries, including rashes, coughing, nose or throat pain, eye irritation and bouts of asthma, health experts warn.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
Maintaining chlorine levels of 10ppm or higher for extended periods of time can not only ruin your liner and cover but also severely damage your pool equipment. Chlorine should be maintained ideally between 1.5ppm to 3ppm.
You want some clear area between the edge of the pool and the cover to pour chemicals. You don't need to remove the cover, you just need enough room so you aren't splashing any full strength chemicals on the cover. When you are done with the chemical addition you can pull the cover back into place.
Is It Safe To Run The pool Pump With The Pool Cover On? It is safe to run the pool pump and filter with a swimming pool cover on. The pool cover doesn't in any way stop or hinder the pool pump from circulating the water or carrying out its function.
Typically for granular shock, you'll need one pound for every 10,000 to 13,500 gallons of pool water.