How long does it take for a cloudy pool to clear? Depending on how cloudy your water is, it may take 2-3 days for your water to clear. If you're using a clarifier, you'll need to run your filter 24/7, keep your water chemistry balanced, and add the proper amount of water clarifier every other day until it's clear.
However, sometimes a balanced pool will become cloudy immediately after being shocked. This typically clears quickly on its own and shouldn't be considered a problem. Environmental factors include pretty much everything around the pool like severe weather, wildlife, construction, trees, pool algae, and people.
It's usually just a temporary reaction as the sanitizer works its magic, and doesn't always indicate a problem. But if the cloudy water persists long after you've shocked the pool, you're likely having an issue with water balance, circulation, or filtration.
For the most part, yes. It can be unattractive and it should be addressed, but it is mostly safe to swim in cloudy water. The only exception would be if the pool is cloudy because there are too many chemicals in it. This pool water would be unsafe to swim in and should be avoided.
In theory, if you have a cloudy swimming pool, you can add chlorine to “shock it” and clear things up. Chlorine will get the job done. But, the amounts may vary and you may have to really pound the pool with chlorine to get the water totally clear.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
The water's pH may be too low or too high.
Lower than 7 indicates an acidic pool, but higher than 7.8 is too alkaline. A pool measuring at either extreme will likely be cloudy. High pH often indicates excess calcium deposits, and low pH often indicates more chloramine and less free chlorine.
If the chlorine smell is very strong, however, you may soon spot “red-eyed” swimmers emerging from the pool. That's when the pool water is assumed to have “too much chlorine” in it. Ironically, a strong chemical smell around the pool and “swimmer red eye” may be signs that there is not enough chlorine in the water.
Baking Soda
Most remedies call for adding additional chlorine into the water. If your water's pH balance is between 7.2 and 7.5, however, you can add baking soda to the water to help clear it up. This serves as a replacement for chlorine because baking soda is a natural cleaning agent.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity.
It's not a good idea to use pool shock at the same time as clarifier. Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.
Skim the top of the pool for debris that may have settled on the pool surface. Add one pound of diluted granular shock to the water for every 7,000 gallons of pool water. Run the filter for 24 hours and retest the water. The slimy looking film can be an early onset of algae.
Run your filtration system for eight hours every day over summer. Back-wash it if you have a sand filter and clean cartridges with Filtrite Filter Cleaner and Degreaser. Add 50 grams of Sanit-eezy Performance per 10,000 litres of pool water. No-one should swim for at least 30 minutes after this.
But excessive exposure to chlorine can cause sickness and injuries, including rashes, coughing, nose or throat pain, eye irritation and bouts of asthma, health experts warn. Instructions for safely chlorinating a pool usually call for a maximum of four parts per million when people are in the pool.
Pools will naturally gas-off chlorine from the surface, and very high levels can irritate airways and lungs. This is especially true for indoor pools. At chlorine levels over 10 ppm, swimsuits can begin to fade. Pool covers become damaged, and the water is generally uncomfortable and unsafe for swimmers.
When the levels are properly balanced, chlorine will keep the algae at bay, but the water will slowly begin to turn green as the algae take over if there's not enough. But be careful—adding too much chlorine in pool water can cause those metals to oxidize and turn the pool a different shade of green.
Here is why: Sunlight is white, which is made up of all the colours of the spectrum. The molecules in pool water absorb light from the red end of the spectrum when sunlight falls on the water. By removing the red, the light which ends up being reflected has a slightly blue hue which can vary in richness by water depth.
The simple answer is No. Baking soda cannot be used to clear up a cloudy pool because it is a base. Bases raise PH levels, which causes the water to turn cloudy. Some people suggest using baking soda as a quick fix to high alkalinity levels, but it's not reliable as a pool chemical.
The fastest way to clean a green pool is by using pool chemicals and your pool filter. This process usually takes around 4-5 days but you will start noticing a major improvement after 24 hours.
To maintain a clear sparkling pool add 4 fluid ounces of Water Clarifier per 10,000 gallons of water weekly. If the pool is cloudy due to dust or to high hardness of the water, add 32 fluid ounces of Water Clarifier per 10,000 gallons of pool water.