Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
In order to prevent residual blow back into the pool, once you've finished backwashing it's highly advisable to rinse the filter. Just as the backwash lifts and flushes the sand, the rinse resets the sand to its original position for optimum filtration.
Most pools must be backwashed and rinsed every two weeks.
"When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use. Additionally, there are several instances that would require backwashing in between the normal monthly backwashing.
Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
The 'Rinse' setting should be used after backwashing and again run just for a minute or two. On this setting the water is flowing through the filter in the normal direction but once again is being sent to the waste pipe rather than being returned to the pool.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
Any backwash water is to bypass the septic tank and be discharged to the drain between the septic tank and the common effluent drain. Under no circumstances should backwash water be discharged into the septic tank.
As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter's pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
Your pump may be too large or the sand level too high in the filter. When the filter is backwashing the water flow can cause the sand to rise high enough and overflow into the standpipe, which will allow the sand back into the pool.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
After backwashing, new DE must be added to the filter. Add the entire amount of DE the filter recommends. If you see DE returning to the pool, vacuum it to waste, after it settles. The next time you backwash and recoat, decrease the amount by 1 pound.
Backwashing is a filter cleaning process through your filter system that reverses the flow of water. Pool filters allow the removal of organic material by directing the water into a porous medium such as sand.
Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs. In general, you shouldn't be losing sand from your sand filter. Nor should any sand be coming out during backwashing, rinsing or filtering.
If anything could be considered “normal”, it would be about 10 psi. Most filter systems are designed to operate in the 5-15 or 10-20 psi range. The way to find out your particular correct pool filter pressure is to clean or backwash the filter thoroughly and empty the pump and skimmer baskets.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading.
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value's waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter. Closed: if you choose this setting, then the flow of water to the pool and filter will be stopped.
Replacement sand for your sand filter typically costs around $25 per 50-pound bag, and your filter may require 100 to 600 pounds or more depending on the size and model. More than likely, you'll need about 350 pounds of sand for an average-sized inground pool filter.
Now, here answers the question earlier: do you leave skimmer basket in when vacuuming pool? YES, you need to remove the skimmer or strainer basket before attaching the open end of the hose to the inlet. Finally, plug the open vacuum hose into the suction port.