We recommend waiting at least 15 minutes to swim after adding algaecide to your swimming pool. Most algaecides are perfectly safe to swim with.
Alkalinity Balance, pH up, pH down, Calcium Balance, Water Stabilizer, and clarifier are all swim-safe chemicals. Wait about 20 minutes, and you are free to swim. We suggest adding algaecide, Super Erace, and shock at night, after everyone is out of the pool. It is safe to swim again the next day.
Now is the time to add Pool Clarifier and let it circulate for 12 hours. This will clump the algae together into vaccumable pieces. Shut your pump off and let the cloudiness settle. This may take up to a few days for very cloudy pools.
pH, Clarifier, Alkalinity — For these types of water-balancing chemicals, it's suggested that you wait at least 20 minutes before you get into the water. After you shock the pool — As soon as your chlorine levels reach 5 ppm or lower, it's officially safe to swim.
Yes, it's normally safe to swim almost immediately (about 20 mins). But check the directions on the pack first. Swimming in your pool after adding clarifier is good for the circulation of the pool water and helps to stir up the particles on the floor of the pool so they can then be sucked in by the pool's filter.
Clarifier works to clear mild cloudy pool water. Add it every other day as your filter runs until your water clears. If you have extremely cloudy water, you need to use a pool flocculant.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
Your chlorine levels won't return to normal right after you shock your pool anyway, so we recommend waiting at least 24 hours to add algaecide. When adding algaecide to your pool, make sure you add the correct amount.
It will make those particles stick together so they will sink and then can be vacuumed (just like flocculant). This stuff does absolutely work for that purpose and will clear up your water in those instances. However, if your cloudy water is being caused by organics or algae, clarifier will not do anything.
What happens when you add too much clarifier is that all the little particles clump together too much an end up as a colloidal suspension. When that happens, the whole thing turns cloudy. It'll clear but it will take a while. Run the filter 24/7 until is clears.
When should Pool Clarifiers be Used? Pool Clarifiers are not meant to be used all season long, but are quite helpful at pool opening, after an algae bloom, or battles with cloudy pool water. Follow label directions, but most pools can be retreated after 5-7 days, with a lower dosage than initially used.
And how long do you have to wait before you can swim? You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
Generally you will want to wait at least 4 hours, but ideal is waiting for one complete turnover of the water (the time it takes all the water to go through the filter).
You can swim with chlorine tablets in the pool if the chlorine tablets are in a container. Getting in touch with those tablets can cause rashes, irritation and eye problems. However, to be in a safe zone it will be better if you wait for 3 to 5 hours till the chlorine levels touch 4 to 6 ppm.
To maintain a clear sparkling pool add 4 fluid ounces of Water Clarifier per 10,000 gallons of water weekly. If the pool is cloudy due to dust or to high hardness of the water, add 32 fluid ounces of Water Clarifier per 10,000 gallons of pool water.
OVERVIEW. Clorox® Pool&Spa™ Algaecide + Clarifier prevents and treats pool algae and includes a built in clarifier to keep water clear. Being one step ahead of algae is crucial because as algae grows, chlorine must work harder to keep your pool clean.
Never add chemicals at the same time, whether you're balancing the water, shocking the pool, or adding a specialty chemical. For most water balance changes, the pump needs to run on the high setting for at least four hours before you can add another chemical or retest the water.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.