You may just be using it incorrectly. Do this: Next time you have a clog, use your plunger like this: Ensure the flange lip is unfolded. Get a good seal on the toilet drain (that is, make sure you're covering the entire drain or you won't have enough pressure to loosen the clog.)
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
When you have a clogged toilet, but you don't need to use it right away, you might wonder if you can just wait and let the clog sort itself out. Will a toilet eventually unclog itself? It sure would be nice, but it's fairly rare for a toilet's clog to clear up after a few hours.
Attempting to force a clog through a toilet with a plunger can often make the problem worse. Instead, create a seal and slowly push down on the plunger before pulling it back sharply. The suction can help pull the clog back up toward the bowl, breaking the blockage and allowing gravity to take over.
The longer you leave a clog, the more opportunities there are for the clog to get worse. The most water-soluble parts of the clog will dissolve, and the rest will fill in the gaps, making the clog worse. There is also the possibility that human error could come into play.
Ideally, no more than five or 10 minutes. One plumber told us that if plunging goes on any longer, it's time to try a toilet snake or call an expert.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
Plunging down too hard
And a really hard thrust could even crack the bowl. The proper toilet plunging technique: Place the plunger in the toilet bowl so that water is covering the lips of the plunger. Push down gently to get all the air out of the plunger and to get a good seal.
One of the most popular methods of unclogging a slow draining toilet is using hot water and liquid soap. Pour the boiling water into the bowl and then add the liquid soap. Let it sit for about 15 minutes before flushing.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
The most common causes for a slow-draining toilet are: A clog in the drain line. A blockage between the tank and bowl. Poor or Clogged Venting.
Start slow and add force as needed. Several gentle pumps will usually work better than a couple of hard pushes. If your blockage is going to come out, it should happen in less than 10 minutes.
If you find yourself with a clogged toilet, you don't have to call the plumber immediately. The first thing you need to do is turn off the toilet's water supply. This will stop the toilet from overflowing.
Then pull up sharply to disturb the clog and loosen it. Continue vigorously pushing and pulling until the water begins to drain. It may take 15 to 20 cycles before the toilet unclogs. Be patient.
Warm Up Your Plunger
Stiff, hard plungers don't work as well as soft and pliant ones. Run your plunger under some hot water before you use it. This will soften up the rubber, which will help you get a better seal on the toilet bowl.
Soap and Hot Water - Remove some of the water in the toilet with a cup or bowl to make room for adding about a gallon of water. Put a soap dish, shampoo, or slivers of bar soap in the bowl. Then heat a gallon of water to the temperature of hot tea, pour into the bowl, and wait about 20 minutes.
For preventive drain cleaning, you can use Drano® Max Build-Up Remover in drains, toilets and even septic systems. Apply Drano® Max Build-Up Remover overnight or before you go to work, then wait 6 to 8 hours before running warm (not hot) water down treated drains or flushing treated toilets.
If you have a toilet that doesn't fully flush, common causes include a clog in the trap, a worn-out flapper, blocked rim jets, a faulty float, or an issue with the handle and chain.
With time, baking soda and vinegar may work as a natural drain cleaner on weaker drain clogs, and the benefits of regular drain cleaning can help keep your drains free of clogs. But for tough drain clogs that need to be dissolved right away, you may want to use a stronger drain cleaner, like Liquid-Plumr.
If the baking soda and vinegar method doesn't unclog the drain, use the salt and baking soda method next. This works best if you do it right before bedtime since the drain won't be used until morning.
You can also pour vinegar down the drain on its own.
Pour about 1 cup of vinegar down your drain and let it sit for 30-40 minutes.