How do you reset the control panel on a Whirlpool washer?

Author: Mrs. Cathrine Mraz V  |  Last update: Friday, May 2, 2025

6 Ways to Reset Your Whirlpool Washer
  1. Press the "Power" or "Cancel" button to turn off your washer.
  2. Safely unplug the washing machine from the power outlet.
  3. Leave the washer unplugged for about 5 minutes.
  4. Reconnect the washing machine to the power outlet.
  5. Press the "Power" or "Start" button to turn your washer back on.

How to factory reset a whirlpool washer?

For top-load models, reset by turning the cycle selector knob to the "Normal" position. Then, turn the knob counterclockwise for one click, clockwise for three clicks, counterclockwise for one click, and finally clockwise for one click. Press the start button to complete the reset.

How do you reset the control board on a washing machine?

To reset the washer's control panel:

If your washer is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the washer is hard-wired to the power supply, turn the breaker off at the home electrical panel that powers the washer for one minute and then turn the breaker back on.

How do you force a washing machine to reset?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

How to restart a whirlpool washer after pausing the top?

Simultaneously press "Start" or "Pause" (depending on your model), and "Cancel" or“Power” buttons at the same time. Hold the buttons for about 5 seconds. Release the buttons and run a short cycle to check if the washer has been reset.

How to Do a Whirlpool Washer Reset & Recalibration

When I press start on a washing machine, nothing happens.?

Cause 1: Unplugged power source. Cause 2: Overheated machine. Cause 3: Wrong settings. Cause 4: Malfunctioning lid switch.

What is the most common problem with Whirlpool washers?

A start button on your washer's control panel not working despite the rest of the lights coming on is the most common Whirlpool washer issue you will encounter. Taking off the control panel to try and find the cause will let you see if the solution can be DIYed, or a professional needs to be called.

How do I know if my washing machine control board is bad?

Symptoms of a Bad Control Board
  1. No Power or Unresponsive Machine. If your washing machine doesn't turn on or respond to inputs, the control board may be at fault. ...
  2. Erratic Behavior. Washing machines should operate in a predictable manner. ...
  3. Display Issues. ...
  4. No Response to Settings. ...
  5. Burning Smell.

How do I clear the error code on my washing machine?

Switch off the appliance at the mains then wait 30 seconds. Switch the appliance back on again and start a new program. If the information code remains, contact a customer service center. Operating the washing machine with the lid open.

How do I clear the code on my Whirlpool washer?

System Error Code

How to fix the error: For a top-loading washer, press start and pause at the same time to clear the code; then press start and pause again to reset the washer. For a front-loading washer, unplug it for one minute, then plug it back in.

Why is my Whirlpool washer stuck on sensing?

The most common cause of a Whirlpool washer that is stuck on sensing is a faulty actuator. However, this problem may also be caused by a clogged drain pump, a failed door latch/lid switch, a torn drive belt, a faulty pressure switch, or faulty water inlet valves.

How to do a hard reset on a Whirlpool washing machine?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.

How do you reset your washer machine?

If you want to try resolving issues with your washing machine, such as power surges or error codes, it's possible you might need to perform a quick reset. One way you can reset a washer is by unplugging the unit for at least one minute, then plugging it back in and restarting the appliance.

Why does my Whirlpool washer keep shutting off?

The main reason this occurs is you have too many other appliances also running through the same circuit as the washer. The best way to stop this happening is to use an exclusive circuit for your washing machine. To check the circuit breaker, go to your household fuse box and make sure it hasn't tripped.

How do you reset a locked washing machine?

If the plug is difficult to reach, or is hard-wired to the power supply, shut it off at the breaker. 2. Wait for a minute: Wait for 1-5 minutes before plugging the washer back in to reset the internal systems. This allows any residual power to clear and can help reset the door lock mechanism.

What to do if the whirlpool washer won't unlock?

If the door doesn't open as it should after the cycle has ended, the next step is to hold the “control lock” button down for 3 seconds. You should be able to hear an unlatching sound followed by being able to open the door.

How to fix control locked on Whirlpool washer?

All you need to do is press and hold the end of cycle button for 3 seconds and the control panel will unlock.

How do I turn off Ctrl lock?

Go to Start / Settings / Control Panel / Accessibility Options /Keyboard Options. b. Turn off CTRL lock if it's on.

Previous article
What to apply on the body before a steam bath?
Next article
What liquid do window cleaners use?