Author: Alaina Cormier | Last update: Wednesday, December 13, 2023
How do I reset my Powerbolt?
Remove batteries.
Push program 3 times.
Push all the buttons on keypad in sequence.
Push the lock button.
How do I reset my Kwikset Powerbolt lock code?
Press the PROGRAM button twice, enter the same or a new code and then press the LOCK button once. If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour.
How do I reset my Kwikset Powerbolt 2 user code?
Press and hold the “Reset” button for 5 seconds. You will hear 3 long beeps after the 5 seconds is completed indicating the lock has been reset. A User Code is used to unlock the door while a Mastercode is a password for making changes to the lock features.
How do I change my keypad lock code?
5 Steps to Change Master Code on Keypad Door Lock
Step 1: Make sure that the door is open and unlocked. ...
Step2: Touch the Keypad & Enter Codes. ...
Step3: Enter *+01+# ...
Step4: Enter Old Master Code +# ...
Step5: Enter New Master Code. ...
Step6: Repeat to Enter New Master Code.
What do I do if I forget my Mastercode on my Powerbolt 2?
What do I do if I forget my mastercode on my Powerbolt 2? If you do not have the master or user code you may do a factory reset on the unit to program a new master code into the lock.
How to Program Kwikset Powerbolt 2 Deadbolt Lock
How do I change my Kwikset 264 lock code?
How do I add/delete a user code on my 264 Deadbolt?
Enter your Programming Code.
Press ""Kwikset"" then ""1"" then ""Kwikset""
Enter a new User Code. It must be between 4 and 10 digits.
Press ""Kwikset""
Test the code: While your door is open, lock it and enter your new User Code to make sure it unlocks the door.
What is the default code for keypad door lock?
Because most of the default code of the keypad door lock are very simple when they are set at the factory, either 00000 or 1234, which can be easily deciphered by strangers, it is very important to change a use code that only you know and is not easy to be guessed by others.
Why is my Kwikset lock code not working?
Make sure the User Code is correct and that the Kwikset button is pushed after entering the User Code. If the door still won't unlock, use a key to unlock the door. Call technical support for further troubleshooting.
Which Kwikset model do I have?
You can identity the type of Kwikset lock you have by locating a small vertical slot on the plug. This is located to the left of the cylinder's keyway.
What is the default code for Kwikset 264?
If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps. Note: If the lock is muted, you will not hear the lock beeping. Delete User Codes:The lock is pre-programmed with a default User Code of 1-2-3-4.
How do I change the code on my Kwikset Smartcode 915?
Make sure the door is open. Press the Program button once.
Press checkmark symbol once.
Enter user code. A total of 16 user codes may be programmed. Each user code must be a unique code between 4 and 8 digits.
Press lock symbol once.
How do I change my Kwikset 910 code?
Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds). 2. Enter new Mastercode.
How do I remove a user code from a Kwikset electronic deadbolt?
On my SmartCode 955, how to delete individual user codes?
Make sure the door is open.
If you have not enabled a programming code, press and release the program button. You will hear two beeps. ...
Press 2 to delete a user code. ...
Press Kwikset.
Enter the user code you wish to delete. ...
Enter the user code again.
Press Kwikset.
How many codes can a Kwikset door lock have?
How Many Guests Can I “Invite” to access my Premis lock? You can invite up to fifteen(15) Apple HomeKit to access your Premis lock through the Home app. You can also provide up to 30 user access codes using the Premis App.
How do I change the code on my Kwikset SmartCode 913?
How do I program my SmartCode 913 lock?
Open the door.
Remove battery cover.
Press the program button once.
Enter new user code.
Press lock button.
If programming is successful the keypad will flash green once, and you will hear one beep.