How do you maintain a pool with a sand filter?

Author: Maeve Brakus V  |  Last update: Friday, July 1, 2022

In order for your sand filter to work optimally, it is important to clean the filter sand regularly.
  1. Stop the pump.
  2. Close the valves on the suction and return lines.
  3. Open the cover of the pump and empty the filter basket.
  4. Refit the cover.
  5. Open the valve to the drain outlet.
  6. Turn the lever to BACKWASH.

Do you use pool chemicals with a sand filter?

You need chemicals with a sand filter because they require sanitization, phosphate removal, pH adjustments, and alkalinity alterations.

How often do you clean a sand pool filter?

There are three main types of pool filters: Sand filters, DE filters, and cartridge filters. In general, a sand filter lasts longest between cleanings and is easiest to maintain. A sand filter usually only needs to be cleaned every 5 years or so. A DE filter requires cleaning at least once annually.

How do you care for an above ground pool for dummies?

Here are 10 key tips for above ground pool maintenance.
  1. Install a Sump Pump in Your House.
  2. Test the Chlorine Level.
  3. Do Weekly Shock Treatments.
  4. Test the pH Level.
  5. Run the Pool's Pump at Least Eight Hours a Day.
  6. Regularly Clean and Replace the Filter.
  7. Regularly Clean Out the Pump and Skimmer Baskets.
  8. Vacuum Often.

How much chlorine do I add to my pool?

The most important factor though is the size of the pool. You'll need about 52-104 oz of liquid chlorine per 10,000 gallons of water. This amount should get the chlorine level to between 5 and 10 ppm.

How to clean a pool sand filter - step by step

How long should I backwash my sand filter?

After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear.

Why do I have to backwash my sand filter so often?

Whenever the filter fills up with the dirt/debris it reduces the flow of water to your pool. Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear.

How long do sand filters last?

Your sand filter can last anywhere from 15 years to 25 years or more if cared for and maintained well. Most of the time, you may need to replace parts like valves and gaskets, but you probably won't need to replace the whole system for many years.

Where do you put chlorine tablets in a sand filter?

ALWAYS Add Chlorine Tablets To Your Skimmer, Floating Dispenser, or Automatic Chlorinator
  1. Skimmer. Adding chlorine tablets to your skimmer is one of the best places to dispense chlorine and it is also the easiest. ...
  2. Floating Dispenser. Floating dispensers are also very simple to use. ...
  3. Automatic Chlorinator.

Can you put chlorine tablets in Intex sand filter?

If you opted for the Intex Salt Chlorinator, you can make your own chlorine by adding the correct amount of Pool Salt to the water. Otherwise, most Intex pools use 3″ chlorine tablets in a floating chlorinator. Use 1-3 tablets at a time, depending on your pool size.

How many bags of sand do I need for a pool filter?

Changing the pool filter sand is a bit of a pain, especially in the back region, but a bag of pool filter sand costs around R90 at your local Builders Warehouse, and you should only need two bags for most pool filters.

How do you backwash a pool with a sand filter?

How to Backwash a Pool Sand Filter
  1. Turn off the pool pump.
  2. Set the filter valve handle to the 'Backwash' position and ensure the handle locks in place.
  3. Turn the pump on and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear.
  4. Turn off the pump.

How do you deep clean a sand filter?

A deep clean is done once a year using a sand filter cleaning solution.
...
  1. Turn Off Your Pool Pump. Any time you're performing maintenance on your sand filter, you need to start by turning off the pool pump. ...
  2. Set The Valve To “Backwash” ...
  3. Attach Your Backwash Hose. ...
  4. Backwash The Filter. ...
  5. Set The Valve to “Rinse” ...
  6. Finishing Touches.

How long do you rinse after backwashing a pool?

Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.

What's the difference between rinse and backwash?

Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.

Can you backwash a pool too much?

Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.

Do you lose sand when backwashing?

When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.

How do I know if my sand filter is working properly?

Add diatomaceous earth (DE) to your pool skimmer, stick to around a scoop or two – no more than the size of a 1lb coffee cup. The moment you do this, go to the pool jets to see if it is returning DE into the pool, or if the water suddenly looks cloudy. If it is, you likely have an issue with your filter.

What should the pool filter pressure gauge read?

Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.

How long after adding chlorine Can you swim?

It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.

Where do I put chlorine in my pool?

The procedure for adding granular chlorine is pretty much the same as adding calcium chloride or sodium bicarb to a pool. Measure the dry chemical, pre-dissolve in a bucket, and pour around the perimeter of the pool (never into the skimmer directly).

How often should I shock my above ground pool?

It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry.

Previous article
Does vinegar hurt steel?
Next article
Can you refinish hardwood floors grey?