The ideal time to shock your pool is in the evening after all swimming is complete. In the evening because the sun will not be boiling the chlorine out of your pool, and after everyone is done swimming because shocking is going to bring the chlorine level up to a level that may be irritating to skin and eyes.
Chlorine is a sanitizer, and (unless you use Baquacil products) is necessary for maintaining a clear and healthy pool. Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.
Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
Add Pool Water Clarifier
After your pool water has circulated and your shock has dissipated, it's time to add your clarifier. Clarifier helps bind tiny particles into bigger particles that your filter can capture.
Brown pool water is often caused by metals (iron) becoming oxidized in the pool water. If you shocked your pool water and it turned brown you probably have metals. Oxidized iron usually turns a brown or rusty color in the water.
Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment. Improve filtration with a pool filter cleaner or filter aid like Jack's Filter Fiber.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool. Short answer: No. Chlorine sanitizers and shock are similar but different in strength.
Should the green be due to pollen, there may be little to do in the way of minimizing the discoloration short of erecting a building around the pool. Fortunately, assuming there are no allergies to the pollen, it is safe to swim in a pool with that as the cause for green water.
Green pool water is often caused by the presence of algae in your pool. Algae blooms can appear when your pool has a low Free Chlorine. Exposure to high heat, heavy rain or poor circulation, without the use of a preventative algaecide, also increase your risk of developing pool algae.
You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool. As a reminder, you want your pH to be between 7.2 and 7.8ppm and your free available chlorine to be 1-4ppm for safe swimming.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
Running your pool pump during a lightning or electrical storm should be avoided as a power surge or nearby lightning strike could damage your pump. However running your pump during is beneficial. The extra filtering will help clean out the impurities rain has introduced into your pool's water.
Give your pool a good shock treatment 1 to 2 days before the storm hits. You can bring the chlorine level up pretty high to prolong the pool being depleted of chlorine.
One heavy rain is all it takes to throw off your pool's chemistry by unbalancing the pool water's pH and making it slightly more acidic. This additional acidity and nitrogen provide a breeding ground for algae that will turn your pool green.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
So if you buy liquid shock, be aware that it only lasts one to two months at the most before it starts to lose effectiveness. While many swimming pool chemicals stay good for years if stored correctly, some pool-maintenance supplies expire more quickly.
The cold water, anything below 65°, has an impact on the ability of the chemicals to dissolve properly. I would recommend using liquid chlorine if you have to shock in lower temperatures. You can dissolve granular shock in warm water. Perhaps it will work if you completely dissolve it before adding it to the pool.