- Mix a few drops of mild dish soap with warm water. - Dampen a microfiber cloth in the soapy water and wipe down the stainless steel surface to remove dirt and fingerprints. Rinse: - Use a clean, damp microfiber cloth to wipe off any soap residue. Dry: - Use a dry microfiber cloth to thoroughly dry the surface.
To clean cloudy stainless steel, a simple solution of warm water and mild dish soap can often do the trick. Use a soft cloth or sponge to gently scrub the cloudy areas, following the grain of the stainless steel. Rinse thoroughly with clean water and dry with a soft towel to prevent water spots.
When a stainless steel sink looks dull, it's often because it's been scrubbed with cleanser that contains chlorine bleach, with a bleach-loaded scrub pad, or — worst of all — fine steel wool that comes pre-loaded with detergent and bleach.
If harder stains or rust remains, sprinkle baking soda or another non-abrasive scrub cleaner on a soft, damp cleaning cloth, mixed with liquid soap. Clean problem areas gently, going with the grain of the stainless steel. Spray the surface with vinegar-water mixture or glass cleaner and wipe again. Pat dry.
Spray on Acorn CRES (phosphoric acid) liberally and let sit for 10 minutes over the affected area. Scour the surface with the pad until it is free of rust or visible oxidation. Make sure to follow the direction of any grain lines on the metal surface.
Stainless steel can be repaired if damaged or scratched without having to strip the entire project. All of our coatings are self-annealing and will blend to themselves resulting in a smooth finish. Useful sacrificial coating for easy removal of graffiti, allowing for low effort and low cost removal and re-coating.
Using Baking Soda
It turns out it's probably the most common method of cleaning a stainless steel sink and seeing it shine again. Baking soda is fantastic because it removes food stains, grease and water deposits quicker than anything else.
When oxygen interacts with the chromium present in stainless steel, it forms a protective layer of chromium oxide on the metal's surface. This layer is responsible for the metal's signature shine. However, if this protective film is damaged or stripped away, the underlying metal can oxidize, leading to discoloration.
Vinegar is highly acidic and should (almost) never be used on stainless steel because it can begin to eat through the protective coating over time. While it may not be evident at first, you will gradually start to dull the surface as the acid eats its way through the exterior coating and will make an uneven finish.
Sprinkle baking soda onto the damp basin and scrub gently. Rinse Well: Rinse the sink with water after cleaning. Polish for Shine: To restore shine, polish the basin with bar keepers friend. If you prefer a more natural approach, try distilled white vinegar.
Fortunately, this is very easy to do! Mix up a 3:1 solution of water and vinegar (any kind), put the solution in the affected pot or pan (make sure to completely submerge the mineral deposits), and turn heat it up on the stove.
After cleaning with a vinegar-based solution, rub oil onto the stainless steel surface–first wiping in the direction of the grain, then in a circular motion to polish and shine. Most oils work equally well, but olive oil, mineral oil, or almond oil are all good choices.
Baking soda is a powerful all-purpose cleaner. Its slight abrasiveness won't harm your stainless steel, but it will help unstick stuck-on stains. Make a thick paste with baking soda and water, and apply it to tough stains. Let it sit for 20 minutes, then wipe, rinse, and dry.
Key processes for polishing stainless steel include cleaning the surface, sanding with progressively finer grits, and buffing with the appropriate compounds. You can also use natural alternatives like baking soda and vinegar for minor polishing tasks.
Apply a bit of baking soda on the surface, then apply white vinegar (it can be in a spray bottle or a small amount dabbed on a kitchen towel). Gently wipe away the spot with a soft cloth or paper towel and rinse with warm water. Another insider secret for banishing buildup, according to Shimek, is to use club soda.
A stovetop cleaner such as TriNova is also effective in cleaning grimy stainless steel range hoods as well as oven and dishwasher doors. More great options for cleaning stainless steel are a grill cleaner or even a silver polish like Wright's.
All in all, WD-40 does an amazing job at cleaning and polishing stainless steel. The only downfall it has is that it has a very unique smell. If you're a guy like me, you've been in the service industry for any period of time, you love that smell. However, your customers may not.
Removal of oxidized stains and even “surface rust” can be done by using a paste made from baking soda and water or a cleaner that contains oxalic acid, such as Bar Keepers Friend Soft Cleanser. If using baking soda and water, use a cloth or soft bristle brush to rub the baking soda paste in the direction of the grain.
Don't Use Magic Erasers on Chrome or Stainless-Steel Surfaces & Fixtures. Contrary to popular belief cleaning stainless steel or chrome surfaces with harsh cleaning tools like scouring pads, SOS pads or others is a big no.
Use only fine-grit sandpaper (400 to 600 grit) that has been soaked in water for several minutes and wrapped around a sanding block to help you lightly buff out the scratch going only with the grain. Clean the surface with vinegar and a damp microfiber cloth to remove all of the grit.
While resistant to the effects of saltwater, environmental fallout, and UV damage, stainless steel will eventually succumb and start to oxidize. The material will start to look hazy, maybe even slightly brown from a light dusting or rust.