You can tip the pool to drain, siphon the water with a hose, then use a wet/dry vacuum to remove any residual water left on the pool floor. Next, using a circular motion, apply the cleaning solution to the surface of the entire swimming pool. This removes dirt, bacteria and other debris that attaches to the pool.
To pick up large pieces of debris, use a plastic leaf rake. The plastic prevents scratches on the pool's liner and bottom but allows you to easily pick up large pieces. For algae and debris, use a thick brush to dig in and drag the algae and debris in one direction.
Use a pool brush to vigorously scrub any pool surfaces covered in algae, including the walls, floors and steps. Apply a green algaecide according to the directions on the label. Let the water circulate for 24 hours, then brush the pool surfaces again. Vacuum or backwash to remove any remaining dead algae.
While larger debris like leaves get sucked up and caught in your skimmer basket, dirt is too tiny to be caught by any netted filters. Instead, it usually falls to the bottom of your pool, and doesn't get circulated through your pool system. That's why you might see dirt piling up in the bottom of your pool.
White vinegar, baking soda, or organic dish soap are great alternatives and can help you tackle most mildew and stains with less health and environmental impact. They're also cheaper than many of the other pool cleaners you can buy. Pro tip: Be careful when using any cleaner to avoid bleaching or fading your liner.
Vinyl liners can rip, so you'll want to make sure that you use a brush that is compatible and that you don't use excessive force. For simple stains, apply a mild cleanser directly to the liner and then scrub it with your pool brush or a soft cloth. You can pick up various speciality cleaners from your local pool store.
Don't Drain the Pool
Clean the pool using leaf nets and leaf baggers, to remove 99% of the organic debris. Even if you can't see the bottom, work the floor until your nets come up clean. This is an important step, so don't skimp here. Continue to skim and brush the pool daily during treatment.
You may have wondered before how to clean an above-ground pool. Only pools constructed of plaster, exposed aggregate, or concrete are strong enough to withstand the power of a pressure washer. Any other type of pool, such as vinyl or fiberglass, must be cleaned using chemical treatments or using non-abrasive methods.
This is likely a type of brown algae or mustard algae that has a tendency to float. An algaecide may be needed to kill the algae and drop it to the bottom of the pool where it can be vacuumed to waste.
This can happen when well water is used to fill the pool, or if the pH level of the water is too high. Algae: Algae can also cause dark brown or orange spots on the pool's surface. If the water is not properly sanitized or if the circulation is poor, algae can thrive and cause staining.
Mustard algae is a form of green algae that is highly resistant to chlorine. Special treatments must be used to eliminate it. Mustard algae is yellowish-green in color and often looks like dirt or sand on the bottom or sides of the pool. It brushes away very easily, but returns quickly.
The most important test to take if your pool's still green after shocking is the pH level. Buy a kit or a test strip and test the pH because it will indicate whether you need to add other chemicals. A high pH means your water is alkaline and cloudy, especially after the shock.
bleach to shock your pool.
Pool shock is a chemical treatment that helps break down contaminants – such as leaves, dirt and debris, even oils from your skin -- that can gradually build up in your pool water. Shocking your pool as part of your weekly pool maintenance routine will help keep your water clear and balanced.
Cleaning your pool or hot tub
Shop-Vac offers a simple, quick alternative to cleaning pools without dragging larger pool pump equipment out of storage. Plus, a wet vacuum is a faster and less labor-intensive solution than hopping in the pool and skimming out debris manually.
Shocking your pool is a fairly simple process. Before you begin, uncover your pool, skim the pool, vacuum the sediment, and brush the walls, floor, and coves. Before adding shock, you'll want to protect yourself with the appropriate gear; which includes protective goggles, gloves, and work clothes.