Remove the AC power to the home alarm console from the wall directly. Use your console's access key (or another item such as a small screw) to unlock and open the system's backing. Lastly, disconnect at least one of the wires that are attached to the system's main battery, which is blocky and noticeable in most units.
Unplug the power or turn it off at the fused spur. The panel battery will eventually die leaving the panel disabled. Alternatively turn off the power and remove the batteries in the panel by unscrewing the cover under the front flap, this way the panel is diabled straight away.
You will need to turn the mains of to the control panel, whether at a spur or remove the fuse inside the panel, unplug the leads from the battery inside the panel and also the battery inside the external sounder. This will shut the system down.
Hardwired Smoke Alarms
Locate the main breaker panel for your home. Identify which circuit breaker powers your smoke alarms. Each breaker should be labeled, so look for something that says “smoke alarm” or something similar. Turn off the circuit breaker for your smoke alarms.
Most home monitoring services will automatically dispatch local police if your system loses power. Disconnecting wiring or causing the old system to lose power may set off a false alarm, resulting in an unnecessary emergency response that could land you with a fine.
Most smoke detector and fire alarm models will include a “silence” function. Press this, and the beeping will stop. If the smoke detector/fire alarm continues to pick up on smoke after a short period has elapsed, the beeping noise will start again to ensure your safety.
Find and disconnect the main source of power for the home security system. Your home security system likely has a main source of power, which is a box that is secured to the wall with an outlet. This box is the key to turning off the alarm while there is no electricity.
To disarm, press the “Disarm” button, followed by your 4 digit master code. o Keychain: You may also use your keyfob/remote to disarm the system. You can do this outside your home before you come in, or after you enter your home. If you do it after you enter, you will have only 30 seconds to disarm the system.
Alarm System How to Terminate a Contract
It is within your rights to terminate the contract at any time. To do so, you must simply advise the service provider verbally or in writing, preferably by registered mail.
The alarm in your home security system is designed to be a deterrent to intruders, as well as alert occupants and draw attention to your home, whether that be from neighbours, passers-by or authorities. Systems will sound for about 5 to 10 minutes, depending on the system, before stopping and automatically re-arming.
Every alarm system has a backup battery located in the control panel. Ensuring this battery is well-charged is important, as it's designed to keep your security system running during a power outage. The normal life of an alarm system battery spans two to five years, and you'll be alerted when it needs replacing.
Remove the AC power to the home alarm console from the wall directly. Use your console's access key (or another item such as a small screw) to unlock and open the system's backing. Lastly, disconnect at least one of the wires that are attached to the system's main battery, which is blocky and noticeable in most units.
Once you've verified that there is no intrusion or threat, clean your device and make sure the sensor and magnet are aligned and that they haven't been altered. After you've cleaned and checked the alignment of your door sensors, reset the door sensor and see if the alarm stops.
Simply cut the power supply to the system by turning it off, unplugging its transformer, and removing the backup battery. After a couple of minutes, replug everything you just unplugged, and the system should come back completely reset.
For many of our most popular systems, beeping alarms and low battery trouble beeps can be silenced by pressing the [OFF] or [#] buttons from the keypad.
Alarm batteries in the panel act as a vital backup in case there is loss of mains power. If fully charged and in working order, a panel battery can keep your alarm working for upto 12 hours without mains power. Batteries in wireless sensors are their only source of power.
Use a pair of pliers to remove the appropriate fuse. That should take care of the alarm in all cases except one (noted below) since the alarm won't run without electricity.
If you have a wireless burglar alarm, it shouldn't cost you anything to remove. That's because you can just unscrew it from the wall yourself. On the other hand, if your burglar alarm is wired in, you'll want a professional to safely disconnect it for you.