Hold down Hush/Test button. This drains any residual power in the alarm and stops any random chirping.
Reset the Smoke Detector: Sometimes, a smoke detector just needs a good reset to stop the chirping. You can do this by turning off the power at the circuit breaker, removing the detector from the mounting bracket and disconnecting the power supply. Then, press and hold the test button for about 15 seconds.
To get your smoke alarm to stop chirping if you've already changed the battery, first try draining any residual charge by holding the test button down for 15 seconds. If this doesn't solve the problem, clean the unit. A blast of compressed air will often remove the dust particles that are causing the beeps.
Disarm the alarm system
The process for doing this differs for each system, but one of the following is usually recommended: Enter the passcode and disarm. Arm the system, and then disarm it, immediately. Press the status button on the keypad.
How to Stop the Beeping. The best thing to do if your fire alarm won't stop beeping is to check the alarm for any issues, clean the alarm, then if all else fails, replace the system.
Low batteries are the most common cause of random beeping. Open the device and check the battery compartment. Replace the old batteries with fresh ones, ensuring they are installed correctly. After replacing the batteries, allow a few minutes for the detector to reset.
Will a smoke alarm eventually stop chirping? A smoke alarm will eventually stop chirping if it stops detecting smoke or if the condition that created the false alarm is fixed. For example, if dust and debris is causing your alarm to sound, cleaning it will stop it from chirping.
Turn the power supply off at the source and completely power down the system. Then, wait up to a minute to turn it back on. A common cause of beeping is low batteries. If any component of your system operates on batteries, replace them and then reset the alarm to allow the system to register the new batteries.
Dust and debris can easily accumulate inside your hard-wired smoke alarm, causing that incessant chirping sound. This build-up can interfere with the sensing chamber, triggering false alarms. To prevent this, make a habit of cleaning your smoke detectors regularly.
For most devices, find and hold the button on the front of the alarm, until the alarm stops, to reset the device. Or, find the button labeled "Silent" or "Hush" to disable an inactive alarm. Totally disable an alarm by disconnecting its wires.
Pressing the “Test/Silence” button on the front of the unit should stop it from beeping or chirping. If this doesn't work, grasp the device and turn it counterclockwise. It should detach from the base so you can open the battery compartment in the back. Remove and replace the battery to see if it caused the issue.
To reset the Alarm Controller, use a screwdriver to press the House Code button 5 times. The red LED will flash 10 times to indicate memory has been reset.
While your smoke alarm sounds, pressing the hush button will silence the smoke alarm for approximately 10 minutes. The hush feature is typically used where an alarm has been triggered accidently. This provides time to clear the current environment of fumes that triggered the alarm without the alert tone sounding.
A red blinking light can indicate several things depending on the model and make of your smoke detector. Typically, a red light that flashes every 30 to 60 seconds is a standard feature indicating that the smoke detector is functioning correctly and is actively monitoring for smoke.
Remove the batteries and hold down the reset button for 15 to 20 seconds. Reconnect the batteries and alarm. It will most likely beep once as evidence it is working, then it should stop.
First, try the reset button on each smoke alarm. If that doesn't work, flip the circuit breaker off and on. If that fails, you may have to disconnect the smoke alarms and remove the backup batteries inside them one by one. (The batteries are there to protect you during a power outage.)
Low or Dead Batteries
Low batteries are the most common cause of chirping or beeping noises in a smoke alarm. It will usually occur at regular intervals of 30 seconds to one minute.
Press and hold the hush button on the front panel of the alarm for at least 10 seconds. It's usually the only visible button on the alarm, typically labeled 'test', 'hush', or 'silence'. Holding the hush button for different lengths of time has different functions, so try holding for 30 seconds if 10 doesn't stop it.