First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious, as the housing may be hot.
Typically, you'll find it inside the air handler, either next to or above your furnace. In most newer systems, the button is often directly next to the blower motor, while in older systems, it may be harder to spot as it is sometimes underneath or behind the motor.
It's designed to automatically shut off the furnace blower if it overheats. Once the blower cools down, pressing the reset button can help restart the furnace. However, it's essential to understand that not all furnace models are equipped with this feature.
You should not reset the burner more than two or three times, the reason is you may be pumping some fuel into the heat exchanger that is not igniting.
A non-working furnace fan typically stems from electrical issues, mechanical failures, or control problems. Start troubleshooting by checking your circuit breaker, thermostat settings, and air filter condition.
Whether the blades aren't spinning or the fan is making tons of noise, most issues with an electric fan are caused by poor lubrication or blockages in the vents. To solve most problems with an electric fan, disassemble the fan, lubricate the central pin and bearings, and clean out the vent and motor case.
Find the Reset Button – you will then need to find the furnace reset button, which is typically located inside the blower compartment, positioned on the side of the blower motor. Press the Reset Button – If the reset button has popped up, you will need to press it down to reset the furnace.
If your furnace is not blowing hot air, or is not operating at all, a component called the fan limit switch or high limit switch may have malfunctioned. You may also see an error message on your thermostat, or a blinking LED light on the furnace control board.
Steps to Reset Your Furnace
If you can't find a switch at the furnace you can turn off the circuit breaker to the furnace at the main circuit breaker box. Wait about 10 seconds. Turn the switch or breaker back on and check the furnace to see that it has power again.
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
To put it very simply, the furnace fan limit switch is a control that tells your furnace's fan when to turn on and off.
When your furnace runs but fails to blow air, several issues could be at play: Blower Motor Problems: If the motor is malfunctioning or not receiving power, it can't push air through your ducts. This could be due to electrical issues, a faulty motor, or problems with the motor's capacitor.
If the furnace fan is not turning on, that means the furnace blower motor is not working. There are a few reasons this may be happening, including: Thermostat set incorrectly. Blown fuse or tripped circuit breaker.
Most blower motors are controlled by a red or black switch on the side of the unit. Hold the button down for a few seconds (the manual will tell you precisely how long), then release. Replace the Panel and Restore Power.
Leave the breaker(s) off for at least 10 minutes while the system is off and “rebooting.” After 10 minutes have elapsed, go back to the breaker box and flip the HVAC breaker(s) back on.
Mind the safety lock. When resetting your furnace, make sure to press the button only once to avoid engaging the safety lock. Reach out to professionals. In most cases, the safest course of action is to contact your go-to HVAC company if your furnace doesn't work after a power outage.
The basic purpose of a reset button is to serve as a safety feature. It helps shut down the furnace when the furnace is too hot. This essentially prevents the overheated furnace from triggering the circuit breaker. As noted above, a furnace may need to be reset sometimes, such as when it is too hot.