Baking Soda and Green, Blue, or Yellow Algae
You'll need to use an algaecide to kill the algae and superchlorinate your pool to clear the water. After this treatment, test your pH and alkalinity and add baking soda to raise alkalinity to at least 100 ppm and pH to between 7.2 and 7.8.
Green algae, unlike its black counterpart, is a true algae; it isn't resistant to chlorine, so you can control it by shocking the pool. If you don't want to spend a lot of money on expensive pool chemicals, you can shock with household bleach.
Algae will remain in your pool after shock if you've had insufficient chlorine and an overabundance of metal elements in the pool water. Therefore, to start the cleaning process. Remove all the debris from the pool with a leaf net and then let the smaller dirt fragments settle.
You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
You need to raise the level of your chlorine – shock the pool – and maintain that high level until all the algae is dead. This may take 3 to 4 days.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you're using.
The solution to maintaining a clear pool is to use readily available liquid bleach as your chlorine source. Chlorine bleach, as discussed above, is not bound to a stabilizer, so when you add chlorine bleach to the pool, it will go right to work killing microbes and sanitizing.
Clorox itself recommends using between 100 and 200 ounces of regular-strength bleach per 10,000 gallons of pool water -- one gallon is 128 ounces, and many bottles of bleach are available in one-gallon or half-gallon sizes. Pool professionals tend to recommend more conservative amounts of bleach.
Calculate the amount of bleach you need based on the fact that 1 gallon will raise the free chlorine level of 30,000 gallons of water by 2 ppm. If you need to mildly shock a 30,000-gallon pool by raising the free chlorine concentration to 5 ppm, you need 2.5 gallons of bleach. To raise it to 10 ppm, you need 5 gallons.
Some of the best natural homemade pool clarifiers include baking soda solution, bleach, white vinegar, lemon juice, rubbing alcohol and borax. Compared to commercial chemical clarifiers natural ones have enzymes that break down the dirt in the water making it easy and cheap to filter them out.
Baking soda can work wonders in a pool. Baking soda can: Help to clear cloudy water and restore the sparkle. Spot-treat algae.
It's not a good idea to use pool shock at the same time as clarifier. Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
There are three main causes for cloudy pool water, including poor filtration, chemical imbalances, or environmental factors, like nearby construction, trees, or wildlife. Filter and pump problems can be caused by a range of different issues.