How do I know what size rollers I need for my garage door?

Author: Felicity Connelly  |  Last update: Wednesday, October 8, 2025

In order to decide what size rollers you need to buy for a replacement, you must measure all the way across the width of the roller head using a tape measure. Standard roller sizes are at one inch, two inches or three inches. Exceptions are sizes that are usually ¼” short: ¾”, 1 ¾”, or 2 ¾”.

How do I know what size my garage door rollers are?

You can figure out this measurement with a ruler across the face of the roller. In addition to the diameter of the roller, you need to know the length of the stem as well. You can get that measurement by measuring the length as pictured above.

How do I know what size roller to use?

When choosing rollers, remember that the curl size is proportionate to the roller size. So, for tight curls, use small diameter rollers; for larger, softer curls use larger sized rollers.

Are garage door rollers all the same?

Are garage door rollers all the same? No, not all garage door rollers are the same. At Precision Garage Door Service, we use high-quality nylon rollers that are quieter and last much longer than vinyl or steel rollers.

How to measure for a garage roller door?

Measuring Guide
  1. Width. Measure from brick to brick in three places, ignoring frames.
  2. Height. Measure from the floor to the bottom of the lintel (horizontal support across the top of the door) in two places.
  3. Pillar width. Measure from the brick face to the returning wall.
  4. Motor side. ...
  5. Top roll height.

Garage Door Rollers - which one to get ?

What are standard roll up garage door sizes?

Roll up doors and overhead doors have no standard height or width. Because loading doors are typically 8-10 feet high and 8-8.5 feet wide (to accommodate standard cargo trucks), most are built to these dimensions.

What size roller for a door?

Although you might think that just taking a typical roller sleeve size of 230mm (9″) is pretty good, this size is more reserved for larger flat surfaces and even if your interior door is larger than most, you'll want to pick up a smaller mini roller sleeve of around 100mm (4″) for the best results.

How often should garage door rollers be replaced?

You should replace your rollers when they stop working well. Depending on the material, that may mean 10 to 20 years, though plastic rollers will need to be replaced well before that. To determine whether you need new rollers, disconnect the door from your automatic opener.

What is the best roller to use on a garage door?

Nylon rollers are a popular choice for residential garage doors. They offer superior noise reduction and better performance than steel rollers. They also require less maintenance than steel rollers, as they don't rust or corrode over time.

What size do garage roller doors come in?

Single roller door sizes are varied from 1200mm(h) x 750mm(w) to 3100mm(h) x 3430mm(w). Double roller door sizes are varied from 2200mm(h) x 3435mm(w) to 3100mm(h) x 5500mm(w). The side room is required to mount the L-shaped supporting brackets as well as the roller curtain guides.

How do you choose your roller size?

Selecting the Right Size

Roller Size and Hair Length: Generally, larger rollers (1.25-2 inches) are best for longer hair, creating loose, voluminous waves and curls. Smaller rollers (0.5-1 inch) are ideal for shorter hair lengths, resulting in tighter, bouncier curls.

What size rollers to get?

When looking for the right hair roller size, it's pretty easy to determine which one you'll need. For more tighter curls, small hair rollers are needed, for looser curls or mermaid waves and some lift, medium hair rollers and for extra volume and soft waves, larger hair rollers will be your go-to.

How do I choose rollers?

The longer in length your roller, the more surface area you can paint, with shorter rollers ideal for edges and corners. Choose your roller cover based on how much area you need to paint. Keep in mind you may need a brush to finish the finer details.

How do you measure roller size?

When measuring a roller it is best to take the measurements with the roller still in the conveyor if possible. Here are the dimensions we need: BF – Between Frame as measured from inside the frame to inside the frame. AL – Total axle length as measured from one end of the axle to the other.

What size is my garage door?

Single garage doors: Most "single car" garage doors measure 8 feet wide by 7 feet high. Double garage doors: Most "double car" garage doors measure 16 feet wide by 7 feet high.

Why won t my garage roller door stay down?

One of the most common reasons a garage door won't stay closed is that the travel limit setting is off-kilter; this feature is responsible for how far up and down your garage door goes, so if it's not properly set, your garage door may fail to close completely.

Should I paint my garage door with a brush or roller?

For best results, use a 3/8"-3/4" roller cover. TIP: For larger areas, consider using a 5-gallon bucket and a bucket grid. With your roller, paint the stiles around the perimeter of each panel. Continue until the garage door is complete.

Are nylon or steel garage door rollers better?

Nylon rollers are known for their quieter operation and reduced friction, making them ideal for homes where noise reduction is important. On the other hand, steel rollers provide exceptional strength and durability, making them better suited for heavier garage doors that need extra support.

How do I know if my garage door rollers need replacing?

Signs That Your Garage Door Rollers Need To Be Replaced

In particular, look for visible damage or signs of wear. This includes cracking and chipping as well as bent and loose components (for example a loose connection between the rod and wheel). Rollers with ball bearings should also be inspected for broken seals.

How long does it take to install a garage roller door?

Q: How long does it take to install a roller door? A: A professional garage door installer takes around 45 minutes to complete the job. However, a DIY installation typically takes around 90-120 minutes, depending on your skill level.

What size roller should I get?

There are two basic sizes for paint roller frames - large 9″ long roller frames and a smaller 4″ style. Decide which roller size to use depending on what you will be painting: Walls and Ceilings - The large roller is better for big surfaces. Doors, Furniture, and Cabinets - A 4" paint roller is ideal.

What is the standard garage door roller size?

The most common residential garage door roller size is referred to as a “2-in diameter,” but the actual diameter is closer to 1 3/4 inches. Commercial as well as industrial garage doors typically use 2-inch or 3-inch rollers.

What is the best roller for metal doors?

1/4-inch, 3/16-inch: For very smooth surfaces like metal doors and plaster. 3/8-inch, 1/2-inch: For smooth and semi-smooth surfaces like drywall. 3/4-inch: For semi-rough surfaces like wood or a textured ceiling. 1-inch, 1 1/4-inch: For rough surfaces like stucco or a heavily textured ceiling.

Previous article
What appliance breaks down the most?
Next article
What is the deflection limit for a foundation?