Sinks generally come in one of three configurations: 6”, 8”, and 6”-16”. The faucet will cover the holes in most of these configuration. You will need to measure the width between the outer holes or estimate it by measuring the width of the deck plate. A 3-hole sink is very common in bathrooms.
Measure the Faucet Center
In other words, measure from the centerpoint of the far left hole to the centerpoint of the far right hole. Most faucet centers range between 4 and 16 inches, with widespread faucets typically measuring at 6 to 8 inches and centerset faucets measuring at 4 inches.
Not all bathroom sink faucets work with every sink, so it's important to make sure the faucet you choose will fit your sink or basin. Standard faucet drillings are centerset, single-hole or widespread. Renovating your bathroom?
Single-bowl sinks may best match up with longer faucet spouts or pull-out spray spouts, while double-bowl kitchen sinks work well with pull-down spray spouts. 2. Finish: Will your sink be made out of stainless steel or cast iron? With a stainless steel sink, a faucet with a stainless look matches up nicely.
'Think of your cabinet hardware and kitchen faucet like jewelry,' says Xander Shreenan of Dowsing & Reynolds. 'One should complement the other; creating a beautiful and decorative kitchen that has been tailored to perfection. ' However, bear in mind that anything too matchy-matchy can look contrived.
The standard faucet hole sizes for kitchens and bathrooms are 1 3/8″ (1.375 Inches or 34.925 mm) in diameter unless otherwise mentioned in the specification. However, faucet holes may vary in size depending on the particular make and model.
Supply lines are flexible tubes that connect your water supply to your plumbing or appliance fixture. They're available in different sizes. The size refers to the diameter of the fittings on either end of the tube, so check your fixtures to see what size you need.
Size of the Faucet
On the other hand, if the faucet is too big, then you may end up splashing yourself every time you wash your hands or rinse the dishes. Not to mention, the faucet will overpower the sink.
A safe course no matter where you buy is to stick with name-brand products known for quality and reliability. Off-brand faucets often are poorly made, and it's difficult to get parts for them.
Faucet Connection Types
Most faucets in the United States will have a 1/2" MPT (male) or 1/2" FPT (female) threaded inlet. These connections use the NPT (National Pipe Thread) standard.
A standard residential faucet supply line has a 3/8-inch compression fitting on one end and a 1/2-inch female NPT fitting on the other.
Replacing a leaky or outdated faucet isn't as difficult as you might think. You can tackle the project with a basin wrench and a few other common tools. It should usually take no more than about an hour. The same steps apply if you're installing a new faucet onto a new sink.
For length and width, measure from one outer sink lip to the opposite side (for most sinks), or from the edge of the counter to the other edge lengthwise (for undermount). For round and oval sinks, measure the diameter, or the length across the widest point of the sink.
Make certain you are choosing a faucet with adequate height to accommodate the items you'll be washing or filling. The higher the spout, the easier it is to fit tall pots under it for filling or cleaning. If you have a shelf above your sink or a wide window ledge, a tall faucet may not fit.
Faucets are not universal, as they come in a variety of sizes, styles, and designs to fit different sinks, countertops, and bathroom/kitchen configurations. Additionally, faucets use different mounting systems and connections, which may not be compatible with all sinks or countertops.
You may need to obtain an adapter in order to connect your new faucet to your pre-existing supply lines or shut-off valves. Moen faucets typically utilize either flexible supplies with ⅜" compression fittings or ½" IPS connections.
The average cost per foot for main water line replacement is $75 to $225. The cost is variable due to the method of installation, the price set forth by your chosen contractor, the length of your main water line (homes set further back from the road tend to pay higher amounts) and the materials used.
Faucet Types
Single-hole faucets are ideal for smaller sinks, such as powder room baths. Their simplicity reflects modern sensibilities. Center-set faucets fit standard three-hole sinks (with outer holes drilled 4 inches apart). They'll have either a single lever or two handles mounted on a 6-inch plate.
Quality Difference Equals Price
The main difference between contractor-grade (bought from plumbing suppliers)and retail-grade (also known as builder-grade, on the shelf at home improvement stores or on-line) plumbing fixtures is the quality of the materials used inside the faucets. Quality equals durability.
So if you have a three-hole sink with the outside holes 4 inches apart, you should be able to install a single-handle bathroom faucet. However, a deck plate to cover all the holes is usually needed. Many single-handle bathroom faucets include an “escutcheon” or deck plate for this very reason.