Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.
Baking soda is safe and straightforward to use, while also providing your pool with a clean, clear, sparkling water that is pleasant to swim in. Baking soda does not sting the eyes; neither can it cause drying of the skin.
There are three main causes for cloudy pool water, including poor filtration, chemical imbalances, or environmental factors, like nearby construction, trees, or wildlife. Filter and pump problems can be caused by a range of different issues.
Baking Soda
Most remedies call for adding additional chlorine into the water. If your water's pH balance is between 7.2 and 7.5, however, you can add baking soda to the water to help clear it up. This serves as a replacement for chlorine because baking soda is a natural cleaning agent.
High doses of chlorine, like pool shock, can cause temporary cloudiness as it kills contaminants. High levels of pH, alkalinity, and calcium hardness are more likely to cause cloudy water.
Add 25ml of Sparkle per 1000 litres of water and pour directly into the swimming pool. Do not add more than 1 Lt in any application for swimming pools up to 50,000 lt capacity. For larger swimming pools dose accordingly.
Remove, clean and replace cartridge, then with pump running, add 8 cups of Sparkle Up per 100 square feet of filter area. Clean cartridges when pool clears, or if filter pressure reaches manufacturer's recommended maximum psi.
The simple answer is No. Baking soda cannot be used to clear up a cloudy pool because it is a base. Bases raise PH levels, which causes the water to turn cloudy. Some people suggest using baking soda as a quick fix to high alkalinity levels, but it's not reliable as a pool chemical.
Skim the top of the pool for debris that may have settled on the pool surface. Add one pound of diluted granular shock to the water for every 7,000 gallons of pool water. Run the filter for 24 hours and retest the water. The slimy looking film can be an early onset of algae.
Low Pool Water Hardness
If your pool water is below 150 ppm, you need to add more calcium. At this point, your water will appear clear and sparkling. But its appearance is deceptive. In this state, the water isn't at a safe level.
If all the chemicals are balanced, but water is still cloudy, there might be fine particles inside the pool, and you need to use a clarifier or pool flocculant and then vacuum up the pool. If all do not work, try backwashing your filter since it might be clogged.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
For the most part, yes. It can be unattractive and it should be addressed, but it is mostly safe to swim in cloudy water. The only exception would be if the pool is cloudy because there are too many chemicals in it. This pool water would be unsafe to swim in and should be avoided.
It's not a good idea to use pool shock at the same time as clarifier. Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
ARM & HAMMER™ Baking Soda is the quick, safe and natural way to open your pool for the season. Use our conveniently sized larger bags to help naturally balance your pH and alkalinity to achieve stunning clear water you can be proud of.
Borax acts as an effective pH buffer and helps prevent algae growth in swimming pools. Plus, it will leave your water looking sparkly and feeling soft.
What can you use instead? Bromine — considered a safe substitute for chlorine. Looks for BCDMH tablets, which are typically 66% bromine and 27% chlorine. If unable to find, you can use just bromine but it may leave the water a dull green color.
To raise the pH levels in your pool, try adding sodium carbonate (soda ash) or sodium bicarbonate (baking soda) until your pool's pH levels are between 7.2 and 7.8.