Depending on your current flow rate, you may be able to increase the flow simply by removing the filter or restricting device or replacing the showerhead with a higher-flow model, such as increasing to a standard 2.5 GPM head. Before you change the showerhead, make sure that the new model is legal in your area.
The most common cause of low shower pressure is a blocked showerhead, as a result of limescale build-up. These blockages obstruct the water flow, leading to reduced pressure over time. Most showers are fitted with a filter, protecting the pipework from debris, but this can become partially blocked by scale.
For water conservation purposes, most plumbing codes require faucets and showering devices to not exceed a certain maximum flow rate. Removing the flow restrictors could cause these devices to no longer meet these codes.
Two big reasons: To help lower utility bills -- and to conserve water. According to the EPA, the average family could save 2,700 gallons per year by installing WaterSense labeled showerheads. Since these water savings will reduce demands on water heaters, they will also save energy.
If your water pressure seems low, the first step should be to test how much pressure you're actually getting from the shower head. A typical home's water pressure should be somewhere between 45 to 55 psi (pounds per square inch).
Open your main water valve.
Your house has a main water valve, usually located near the meter; the valve controls the flow of water into your home's pipes. Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure.
To get back to the important question - yes, a showerhead can help increase water pressure, and it can also do so while consuming less water than your usual fittings. Showery showerheads are designed to increase water pressure so you can experience a more enjoyable shower.
Pressure-Reducing Valve
Look on the main supply pipe near your water meter for a conical valve that has a bolt sticking out of the cone. To raise pressure, turn the bolt clockwise after loosening its locknut. Keep an eye on the gauge to make sure the pressure is within bounds, then retighten the locknut.
If you've just installed a brand-new showerhead and find that the pressure is suddenly lower, it's probably because you've purchased a water-saving showerhead. Check the labels around the rim, or perform the showerhead GPM test as described below.
A fast drop in only one faucet means there's a problem with the faucet. Rapid low pressure affecting one area of the house may mean a corroded pipe issue. An abrupt water pressure drop affecting the whole house may mean a water main break (municipal water) or a well pump problem (well water).
It may be caused by debris such as dirt, sand, solidified oil and grease, food particles, or foreign objects. Pollutants can block pipes if they back up due to fractures in the water main. Mineral buildup clogs pipes over time and causes the water pressure to go down, as there's less space for water to travel through.
Residential water pressure tends to range between 45 and 80 psi (pounds per square inch). Anything below 40 psi is considered low and anything below 30 psi is considered too low; the minimum pressure required by most codes is 20 psi. Pressures above 80 psi are too high.
For a single level home or a two story home without water fixtures on the 2nd floor a 30/50 PSI setting may be sufficient. For two or more levels with water fixtures on more than one level you may want to use 40/60 PSI setting. It's easier for a pump to supply the lower pressures and it's less strain on old plumbing.
Water systems which operate at 1.0 bar pressure (10 m of drop) or greater are considered high pressure systems. Those with a pressure less than 1.0 bar are considered low pressure. When you're ready to choose a tap or shower, you'll find the water pressure it's suitable for will be clearly labelled.
The center of the restrictor is shaped like a star, or similarly shaped, and comes in a variety of colors. It's found behind where the shower head screws off of the pipe coming out of the wall or at the end of the flexible hosing of a handheld shower head.
Do different shower heads affect water pressure? Yes, depending on which shower head you choose, they can increase the water pressure at the head itself in order to create a more powerful shower or decrease it to create a more gentle shower.
A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
Flow restrictors limit the amount of water flowing downstream, while pressure regulators affect the pressure of upstream water by changing the flow of downstream water. Water pressure regulators are not designed to control flow rate. However, they affect flow rate by managing the pressure within a water line.
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992. The step down from there in Flow Rate is 2.0 GPM.