Use a pool brush to vigorously scrub any pool surfaces covered in algae, including the walls, floors and steps. Apply a green algaecide according to the directions on the label. Let the water circulate for 24 hours, then brush the pool surfaces again. Vacuum or backwash to remove any remaining dead algae.
Adding shock to your pool super-chlorinates your water. And this extra dose of sanitizer will kill algae growth. The more serious your pool algae problem, the more shock you'll need. We recommend using calcium hypochlorite shock, or cal-hypo shock, as an effective algae treatment.
Shocking is the process of adding chemicals to your pool to raise chlorine levels and kill bacteria and algae. We recommend using a calcium hypochlorite shock to treat your algae problems.
The only thing that kills algae is CHLORINE (or your sanitizing product, or one of the copper-based algaecides on the market). You need to raise the level of your chlorine – shock the pool – and maintain that high level until all the algae is dead. This may take 3 to 4 days. RUN THE FILTER 24 HOURS A DAY.
There are a lot of reasons why algae keep returning to pools. The most common of these reasons are: Low levels of chlorine or chlorine getting burned up too fast before it gets the opportunity to kill the algae.
Using baking soda in your pool is one of the easiest but most efficient ways to get your backyard ready for summer. This pool idea is loved by experts who recommend using this homemade remedy to increase the alkalinity and pH level of your pool – and treat black algal growth on your swimming pool wall.
It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.
Whether mild or severe, it isn't recommended. Significant amounts of swimming pool algae welcome a breeding ground of harmful bacteria that feed on algae.
Chlorine shock is usually the best way to get rid of green algae. However, an algaecide may become necessary if you're fighting more chlorine-resistant algae, such as mustard algae or black algae. Even then, the pool algaecide should work with chlorine or other sanitizers – not as an alternative to them.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Scrub the black algae away with a good, stiff pool brush. This will help break down the protective layer and make it easier to treat. Break a chlorine tablet in half and rub it directly onto the affected areas. The chlorine treatment will kill the algae's roots and prevent it from coming back.
Apply a mustard algaecide following the label directions. Allow the water to circulate for 24 hours. Use a pool vacuum or backwash the pool again to remove the remaining dead algae. In persistent cases, brush the pool and apply algaecide once more after two to four days.
Once algae gets into your pool water, they can turn into an algae bloom if you have nitrates, out-of-balance chemicals, warm temperatures, sunlight, carbon dioxide, or phosphates. Poor water circulation, poor filtration, and not sanitising your pool will also contribute to rapid growth.
You didn't use Flocculants or Clarifiers. If you still can't see the bottom after shocking your pool, you may need to add a clarifier or flocculant the next day to remove the dead algae. Flocculant binds to small particle impurities in the water, causing them to clump together and fall to the bottom of the pool.
The most important test to take if your pool's still green after shocking is the pH level. Buy a kit or a test strip and test the pH because it will indicate whether you need to add other chemicals. A high pH means your water is alkaline and cloudy, especially after the shock.
If your pool is green and cloudy, it's likely an algae problem. Algae can persist in a pool even after shocking. A green pool – especially one that turned green overnight or after rain, can also be from a pool pump that isn't properly circulating water or an issue with your filtering system.
Barley straw is a natural way to fight algae. On contact with water, the straw starts to break down, and as it does so it releases peroxides into the water which combat algae. Available in mini bales, or as a concentrated extract of barley straw liquid, it's a natural way of chemically fighting algae.
A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool's pH tested below 7.2, add 3-4 pounds of baking soda. If you're new to adding pool chemicals, start by adding only one-half or three-fourths of the recommended amount.
The pH may be too high.
If the pH becomes too high (over 7.8), it prevents the chlorine from doing its job. If you're not checking the pH and it has risen too much, you could be adding the right amount of chlorine, but it can't work correctly, and algae will begin to grow.
So if the pool water isn't cloudy and the 'dirt' is clinging to the walls after brushing, the problem is likely be yellow/mustard algae. Yellow/ Mustard algae is very resistant to even high chlorine levels and will grow and thrive in a chemically well-balanced pool.
Chlorine is still one of the most effective killers of algae so doing a super-chlorination of 10-20 ppm of chlorine can go a long way towards wiping out the algae. Liquid chlorine is an ideal shock for algae because it is fast acting and does not add cyanuric acid (CYA) or calcium to the water.