To sync your Schlage Connect Smart Deadbolt with Z-Wave Plus to your Wink hub, open the Wink app on your mobile device and follow the app's instructions. When you have successfully connected your devices, you will see a flashing green check mark on the lock. The Wink app will also indicate that it has found the lock.
The Schlage Connect™ Smart Deadbolt combines advanced features with the enhanced security of Z-Wave Plus. It's easier than ever to connect to your home automation system and control your lock with your voice.
You can factory default your Schlage Z-Wave Lock by powering down the device and then holding down the Schlage button as power is being reapplied. The device will blink three times to confirm that the reset process was successful. You will need to re-add the device to a Z-Wave network.
Z-Wave smart locks are available from brands like Schlage, Poly-Control and others. Unlike Bluetooth locks, Z-Wave locks don't connect directly with your phone. Instead, they'll need to connect to a Z-Wave-compatible hub.
With a Z-Wave Controller, one can control many aspects of their home. On the security front, you can control your garage door, smart locks, and smoke detectors. You can also control lighting, power outlets as well as monitor water and energy thanks to its numerous features.
It's easy to set up – plug it in within Bluetooth range of the lock (usually about 40 feet), and use the Schlage Sense app to connect the Adapter to your home Wi-Fi network. Then pair it with your lock.
Yes. Both the Schlage Connect lock with Z-Wave technology and Schlage Connect lock with Zigbee technology are compatible with Amazon Alexa-enabled devices.
To sync your Schlage Connect Smart Deadbolt with Z-Wave Plus to your Wink hub, open the Wink app on your mobile device and follow the app's instructions. When you have successfully connected your devices, you will see a flashing green check mark on the lock. The Wink app will also indicate that it has found the lock.
Log in to the Amazon Alexa app and enter your password to enable this feature. Then you will be required to set a four-digit PIN, which must be spoken before Alexa will unlock the door. When you say, “Alexa, unlock the front door,” Alexa will ask for the PIN. If the PIN is correct, Alexa will unlock the door.
You can factory default your Kwikset Z-Wave Lock by removing the lock's cover and then removing the lock's battery pack to power the lock down. Then press and hold the "Program" button. Keep the button held down as you reapply power to the lock. Then wait, and press one more time to reset.
The free Schlage Home app for Apple iOS and Android is your “remote control” if you have a Schlage Encode™ Smart WiFi Deadbolt or Schlage Sense™ Smart Deadbolt. If you have a Schlage Connect™ Smart Deadbolt, you will need to use one of our partners' apps like the Nexia or Samsung SmartThings app.
Because the Schlage Connect is powered by Z-wave, you need to pair it with a smart home hub, like Wink, to extend communication with your home's wi-fi. This allows you to communicate with your lock via the Wink app when you are remote.
Will Z-Wave interfere with my Wi-Fi network? No, Z-Wave operates on a different wireless frequency than Wi-Fi. Even though your smart hub will plug into your Wi-Fi router, the hub communicates with other smart devices on a different frequency making interference nonexistent.
For the most part, your Schlage keypad lock may stop working if the batteries are low or completely drained. If your lock suddenly stops working, the first thing to do is replace the batteries and then try to operate it again. Also, check if the battery connector is disconnected and get it properly connected.
Replace the Batteries
Your Schlage Connect Keypad may malfunction if the batteries are low. So if your keypad suddenly stops working, the first step to resolving this issue is to replace the batteries in your lock. So replace the batteries in your lock to see if that resolves the issue.
To get started, open your door and extend the deadbolt so that it's in the locked position. From there, press the Schlage button at the top of the keypad and enter in your six-digit programming code. Once the programming code is entered, hit “9” on the keypad. You'll get one beep and one blink of the green checkmark.
The Z-wave Plus-enabled Schlage Connect® Smart Deadbolt works with most Z-Wave smart home hubs, including Samsung SmartThings.
The SmartThings Hub is a Z-Wave certified central static controller. It can be included in any Z-Wave network and operate with Z-Wave certified devices from other manufacturers.