In theory, if you have a cloudy swimming pool, you can add chlorine to “shock it” and clear things up. Chlorine will get the job done. But, the amounts may vary and you may have to really pound the pool with chlorine to get the water totally clear.
Excessive levels of pool chemicals can cause your water to become cloudy. High pH, high alkalinity, high chlorine or other sanitisers, and high calcium hardness are all common culprits.
How long does it take for a cloudy pool to clear? Depending on how cloudy your water is, it may take 2-3 days for your water to clear. If you're using a clarifier, you'll need to run your filter 24/7, keep your water chemistry balanced, and add the proper amount of water clarifier every other day until it's clear.
Adding a recommended dose of shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Baking Soda
Most remedies call for adding additional chlorine into the water. If your water's pH balance is between 7.2 and 7.5, however, you can add baking soda to the water to help clear it up. This serves as a replacement for chlorine because baking soda is a natural cleaning agent.
For the most part, yes. It can be unattractive and it should be addressed, but it is mostly safe to swim in cloudy water. The only exception would be if the pool is cloudy because there are too many chemicals in it. This pool water would be unsafe to swim in and should be avoided.
Baking soda can work wonders in a pool. Baking soda can: Help to clear cloudy water and restore the sparkle. Spot-treat algae.
There are three main causes for cloudy pool water, including poor filtration, chemical imbalances, or environmental factors, like nearby construction, trees, or wildlife. Filter and pump problems can be caused by a range of different issues.
A clarifier requires less work and less water but can take to two to three days to achieve the results you are looking for.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
Phosphate removers can also cause cloudy or hazy water as they bind to phosphates and cause them to fall out of solution and precipitate for removal by filtration.
Pool water with a high total alkalinity (TA) is often associated with cloudiness. This is because it can cause an imbalance in the pH levels and lead to calcium scaling. Typically if your TA is higher than 200 ppm, you're at risk of a cloudy pool and just like imbalanced pH levels, your chlorine will be less effective.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity.
Some of the best natural homemade pool clarifiers include baking soda solution, bleach, white vinegar, lemon juice, rubbing alcohol and borax. Compared to commercial chemical clarifiers natural ones have enzymes that break down the dirt in the water making it easy and cheap to filter them out.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
Never add chemicals at the same time, whether you're balancing the water, shocking the pool, or adding a specialty chemical. For most water balance changes, the pump needs to run on the high setting for at least four hours before you can add another chemical or retest the water.
You can dilute the baking soda in a bucket of water or just broadcast it over the entire surface of your swimming pool. It should take about 24 hours before your swimming pool completely clears.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Our Liquid Algaecides are patented formulas that not only work as preventatives but as a pool clarifiers that inhibit algae growth of all types. When included as part of your regular pool maintenance program, Liquid Algaecide acts as a form of insurance against the presence of algae and it's cost associated remedies.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
Just like you run vinegar through your coffee pot to get rid of calcium buildup, white vinegar can wipe away this eyesore in your pool. Mix a 50/50 solution of vinegar and water, dip a sponge or soft cloth into it, and scrub that residue away.