The easiest way to fix a slow draining toilet is to unplug the tank and take it off, then clean out the pipe. If this does not work, you may need to replace the flush valve in your toilet. You will want to turn off your water supply before you begin. There should be a valve in the wall behind the toilet.
There is only one Drano® product recommended for use in slow-running toilets: Drano® Max Build-Up Remover. It contains microorganisms that break down organic matter in pipes that can slow water flow.
Hot Water and Dishwashing Liquid
Pour two cups of dishwashing liquid down the toilet drain. Allow the dishwashing liquid to sit in the drain for 30 minutes. After 30 minutes, pour the hot water into the toilet drain. Let the hot water sit in the drain for another 30 minutes.
Check the water level:
This cause by far the most common reason for slow flushing toilets. If the water in the tank is not up to the recommended level, you may have poor flushing power.
Debris that builds up over time inside the water system, including the valve body, supply line or shut off valve (at the wall) can restrict the flow path of water and slow down the valves filling speed. Toilet fill valves in use for a period of 7 years or more can have their working parts start to wear out.
When the toilet is clogged, it's often possible to unclog the toilet with dish soap. Liquid dish soap is denser than water, so when dish soap is added to water, it sinks. 1 After the dish soap settles, it loosens the obstruction.
Green Gobbler addressed a slow draining sink quickly and easily. Pour it down the drain, wait an hour or two (wait overnight if the clog is bad), run the hottest water for a while, and the drain is good to go.
Heat 1 to 1 ½ cups of white vinegar to about the same temperature you'd take your coffee – not scalding, but warm enough. Add it to the overflow tube and give it about 30 minutes to work. Flush, then go to work on the jet holes, chipping away the scale with something small but solid.
It may be because your toilet drain is clogged, a faulty water tank, low water pressure, or even the design of your toilet. The good news is that it is easy to fix this problem. You can either get in touch with a professional plumber or try it yourself.
This problem is caused by too much slack in the lifting chain that connects the flush lever to the flapper.
If your toilet bowl is full, make sure you remove all but about 2-inches of water before plunging the toilet to prevent water from getting onto the floor. Place the plunger over the drain and pump up and down very quickly. This should help the clog dislodge and make your slow toilet fast again.
Clear any blockages with a wire hanger or vinegar. Ensure the tank's water level is high enough to provide adequate flushing pressure. If your toilet has an adjustable flush valve, experiment with the settings to increase the flush strength. Replace the flapper valve if it's old or damaged.
Throw a Bucket of Water into the Toilet Bowl
One of the simplest ways to manually flush your toilet is pouring a bucket of water into the toilet bowl. You'll just need a bucket containing a gallon or two of water. Older toilets may need 3-5 gallons of water to start the flushing cycle.
It is quite common for minerals such as calcium and lime, along with debris particles such as rust to build up in the rim feed and jet holes of the toilet bowl. Over time, these deposits restrict and block water from flowing into the toilet bowl which will cause a weak or incomplete flush.
Locate the screw that attaches the float to the fill valve (usually on top of the fill valve). Using a screwdriver, turn the screw in small increments to adjust the water level. Clockwise will raise it and counterclockwise will lower it.
You can use straight or a diluted vinegar cleaning solution for the bathroom to clean bacteria, especially around the toilet. Cleaning with a mixture of baking soda and vinegar in the bathroom can work really well. To clean your toilet with vinegar, pour a cup of vinegar in the toilet bowl and let sit overnight.
One of the strongest substances for unclogging a toilet is a commercial drain cleaner specifically designed for toilet clogs. These cleaners typically contain powerful chemicals that dissolve organic matter and stubborn blockages.
Baking soda, borax and tea tree oil combine to make a heavy-duty toilet bowl cleaner. Baking soda, borax and tea tree oil combine to make a heavy-duty toilet bowl cleaner.