Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
Water Pressure Readings
Normal water pressure is generally between 40 and 60 PSI. Most homeowners prefer something right in the middle around 50 PSI. Once you measure the water pressure in your house, you can adjust it to a setting that is ideal for all family members and household uses.
Drop in pressure when running two fixtures at same time
An example of this could be running the faucets in your kitchen and bathroom at the same time. If you notice a decrease while having just these two going, you might have a low water pressure.
Partially Closed Valve
One of the most common issues that can lead to low water pressure problems is that the water is being obstructed by one or more partially closed shutoff valves. Typically, a home will have one main shutoff valve located inside the house.
Place the measuring jug under the tap. Then, turn the tap on full. Time how long it will take for the jug to fill up. If it takes more than 6 seconds to fill it up, then the water pressure is low.
The average flow rate for faucets is between 1.0 gpm and 2.2 gpm. In the US, the maximum flow rate for kitchen and bathroom faucets is 2.2 gpm at 60 psi. In more environmentally regulated areas, the maximum flow rates are further restricted. For example, Georgia is down to 2.0 gpm and California is at 1.8 gpm.
It may be caused by debris such as dirt, sand, solidified oil and grease, food particles, or foreign objects. Pollutants can block pipes if they back up due to fractures in the water main. Mineral buildup clogs pipes over time and causes the water pressure to go down, as there's less space for water to travel through.
Water pressure is measured in psi, or pounds per square inch, and represents the force at which water enters your home from the water main. Normal psi for a home pipe system is between 30 and 80 psi.
If you have high pressure (achieved with or without a pump), you will get a better flow rate and can consider big rain heads, body jets and the ability to have two or more taps or showers on at the same time. A high pressure system will work well with a mixer, electric or digital shower.
Homeowners should start first at one faucet in the house, like the kitchen or bathroom sink. They should turn on cold water first and then hot water, before turning on both, while noting when water pressure is low and when it is not. Next, they should try the water pressure in another faucet by repeating this process.
Do All Homes Have a Water Pressure Regulator? No, and in some cases, you may not need one. Certain municipal supplies regulate their water pressure safely, but if that pressure runs above 80 psi, you'll want to protect your plumbing system by installing one.
You can increase water pressure by loosening a locknut on the valve. Contact a well-pump technician: If your house is on a private well, poor water pressure could indicate a problem with the captive storage tank or the pump. It's best to have the well system serviced by a qualified well expert.
If there's an accumulation of sediments in your hot water tank, it can lower your water pressure. The presence of kinks in the flexible water pipes used in water heaters can result in low water pressure. If the shut-off valve isn't fully open, water pressure can drop.
If you have low water pressure in all your plumbing fixtures, the issue is almost definitely with your water supply or your pipes. However, if it's one or a few fixtures that seem to have a low flow, you may want to check out the fixtures.
For one, tracking down leaks in the system could be a solution. Also, opening a half-shut supply valve that could otherwise reduce flow would do the trick. Replacing corroded and clogged pipes should also improve low water pressure.
An easy way to describe it would be, water flow is how MUCH water flows down a faucet, and water pressure is how HARD the water falls down the faucet. Both water pressure and water flow are related to friction. Friction will slow down water as it moves through a pipe, depending on the pipe's texture and diameter.
The typical residential water flow rate for small households is between 6-12 gallons per minute, so unless you plan to add extra kitchens, bathrooms, or laundry rooms to your home in the future, your home will never need to exceed that final GPM, assuming your flow rate is already normal.
The average American shower uses approximately 15.8 gallons (59.8 liters) and lasts for 7.8 minutes at an average flow rate of 2.1 gallons per minute (7.9 lpm).