Polymeric sand won't wash away during heavy rains and similar weather conditions. With polymeric sand, pavers won't shift after pressure-washing the area. Homeowners don't need to replace polymeric sand continuously. Polymeric sand doesn't hold in moisture, thus preventing the growth of mold and mildew.
Polymeric sand is the most popular and useful filler used under brick pavers. It is a mixture of fine sand, adhesive and is most widely used in paver joints. Typically, polymeric sand lasts for up to 10 years. But if you use high-quality polymeric sand, it can last for approximately 15 years.
Polymeric Sand has many benefits, however, the biggest drawback is that it can be easy to mess up, especially if you don't follow the manufacturer's instructions.
Using a leaf blower, remove excess polymeric sand lying on brick pavers. Use the leaf blower carefully so that you don't blow out the sand from the joints. It is the excess sand that you are targeting. If you do not remove this excess sand properly, it will become wet and stick to the surface.
If remov- ing polymeric sand, a hot water pressure washer will help to soften up the binders in the sand. Any tough to remove hardened areas, may require mechanical means to clean the joint. Take caution with natural stone or thin style pavers and be sure to avoid disturb- ance of the bedding sand underneath.
No, new product won't adhere to the old. You have to remove the old polymeric sand and then apply fresh product for the best result. How to replace polymeric sand between pavers? Inspect the pavers to make sure the sand in the crevices is at least 1/8″ below the top of the pavers.
Traditionally, concrete paver manufacturers have recommended waiting at least 90 days after polymeric sand installation to apply a protective sealant to a paver surface. Nowadays, a 30 day delay is sufficient to allow the evaporation of any remaining natural efflorescence contained in the pavers.
When looking for alternatives to polymeric sand, you will also want to find high quality materials. There are other products, such as EnviroSAND, EnviroSTONE and EnviroPATH on the market that are able to stop water erosion from occurring.
Instead of simply using regular sand to fill in the missing spots between the pavers, build long-lasting beauty into the surface with polymeric sand. If you don't, much of the sand you put in will wash out after a few heavy rains, and you may see weeds pop through before you finish packing up at the end of the job.
Polymeric Jointing Sand is suitable for sweeping into the spaces between paving stones. Once placed and dampened, Polymeric Jointing Sand hardens to lock pavers in place.
Epic Fail #1: Too much or too little watering.
Using too much water can cause the sand to wash out of the joints. On the contrary, using too little can result in the product not setting up properly. Hazing can also occur if sand residue isn't fully washed off the surface of the pavers.
The minimum drying time required for polymeric sand is 24 hours while it takes minimum of 12 hours to cure. But for the vehicular traffic is only allowed on pavers after 48 hours. So, it is wise to avoid foot and vehicular traffic during this process.
A danger of using too much water too quick creates the possibility of washing away the polymers. Too little water used in the installation process could leave you with a fragile joint. If the joint is not properly watered to at least 2/3's depth, a hardened crust may form at the top of the joint.
Any excess polymers and sand should be rinsed off of the project surface. Go over your pavers again with a leaf blower to blow any excess water and sand off of the surface of your pavers. Work in small areas to be sure you remove as much standing water and/or sand as possible.
Polymeric Sand Not Hardening
If it is able to penetrate the sand, then there is a problem. Typically this occurs because there was a rainfall shortly after the installation which caused the sand not to set, the sand was watered for too long, or there is not proper drainage in the base.
Polymeric sand cures by drying. And in order to fully set, it needs to dry out completely. If your polymeric sand didn't harden up, it's pretty much guaranteed there's a moisture issue. If the joints remain wet after the installation, they will remain soft until they dry.
Polymeric sand is appreciated by paver installers because joints you get from it are durable and even . This eliminates any risk of weed growth and ant infestation that could affect the overall aesthetics and durability of paver projects.
We recommend polymeric sand for your Rainier Collection. It is used in the gaps between the stones. The polysand is probably 95% waterproof if done right.
Generally speaking, you'll want to perform three rounds of watering. The initial showering should be done at a height of about 4 ft. Wait no more than three to four minutes before performing the second round of showering at a height of about 2 ft. Lastly, shower and rinse simultaneously at a height of 2 ft.
When pavers are first laid, a block or brick wall is built there is often latent water present in the product. This water may be present due to the manufacturing process, product sweating from long-term packaging, water being added to the product during or after the installation or site moisture.
With regular sand, you should re-sand your pavers at least once in two years. Polymeric sand is usually good for about ten years, so re-sanding costs are saved when using this type of sand. However, this is a very basic estimate, and it actually depends on the conditions faced by your paver, such as weather.
Unlike conventional sand, it stays in place and remains stable. It softens when wet and firms up when dry to better resist soil movements.