In most instances, you'll be able to put tiles over the drywall. Even an area in the kitchen or bathroom, which is subject to some water, can be set over the drywall.
If you're planning on installing both drywall and flooring, it's generally a good idea to install the drywall first. That way, any mess or debris from the drywall installation won't damage your new flooring. Plus, it's easier to cut the drywall to fit around the edges of your flooring than the other way around.
Tile is a finished surface. Drywall is a finished surface (it still needs taping floating and texture etc) a backer board needs to go up before the tile. Every situation I've seen drywall and backer board are up before tile. So drywall goes up before tile.
Do walls sit on top of subfloor? Walls are built on top of a home's subfloor, so replacing the subfloor can sometimes require removing the walls.
Caulk is fine for the perimeter so is spray foam. Don't be hesitant to mix up patch it's like mixing a cake do the patch in small batches and skim it on there with a broad knife. Doesn't have to be pretty. Prime it all with a roller per manufacturer (some primer needs multi coat or diluted).
Other possible solutions for gaps between the wall and the floor caused by less serious problems include using caulking or sealant to fill in the gap. This can be a quick and cost-effective way to address the issue, but it may not be the most permanent fix.
It might sound counter intuitive at first to leave space between your floor and your wall, but you should always leave a ½ inch to ⅝ inch gap between drywall and the floor. There are several reasons for this: Drywall absorbs moisture.
Yes, plywood behind gypboard works as a structural base for shelves. It is a recommended practice for support railings in bathrooms.
Vertical joints in drywall are also called "butt joints." Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall.
Regular drywall can be used as a base for tiles in a shower, but only as an absolute last resort. Even in the best of scenarios, the tile and grout will eventually wear down, leaving behind a clear route for water to seep through and soak into the drywall.
In the end, whether you tile your walls or floor first is down to you and your preferences. If you're working on it yourself and have more time to spare, then tile the floor first as this makes tiling the walls easier. Just bear in mind that you must wait for the adhesive to dry before you begin working on the walls.
It is perfectly safe to put tiles over the drywall of areas in your home that don't have excessive moisture so long as you prep the wall before installation and choose the appropriate mortar.
Joints are too tight
Without enough space when this happens, you'll get cracks. Keep a 1/8-inch space between sheets during installation to keep this from happening. Using a guide can help make sure your sheets are properly spaced throughout the job.
Wall studs are fundamental components of building construction, and you'll find them behind the plaster walls in most buildings. Understanding wall studs helps in identifying ways to enhance a structure, whether through adding extra support or simply mounting a heavy object.
Yes, covering your insulation with a vapor barrier plastic before installing drywall is crucial. It prevents moisture buildup that can lead to mold, rot, and even structural damage. A polyethylene vapor barrier also adds a layer of fire protection, making your home safer.
In terms of strength, plywood is preferred over gypsum board. Its multiple thin layers of veneer help it hold a considerable amount of weight. However, it is more difficult to fix than drywall. Gypsum boards, on the other hand, are prone to crumbling and cracking.
Framing & Drywall
Framing should ideally be done before flooring as well, but drywall is up to you. It is traditionally installed before flooring, but does not have to be.
You may tile over existing tile, painted or unpainted drywall, plaster and textured walls. But tiling over tile can add quite a bit of thickness, so make sure your wall can handle the weight. You should not tile over wallpaper, glossy surfaces, lead paint or plywood.
If you want to fix the gap use a colour matched filler. Either a paste manufactured by Bruce Hardwood floors or one from Dura Seal. Rub and push the filler into the crack and wipe the residue off the floor surface. Then use a soft cloth and with mineral spirits and it should lood good.