There is no magic inside a salt-chlorine generator that balances pool water. All parameters should be checked and balanced regularly. Additionally, salt pools need to be shocked on a regular basis and salt-chlorine generators typically do not have the ability to effectively shock your pool.
So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.
Shock your pool once a week with Salinity Surge Shock or Salinity Oxidizing Shock. Pool shock works as an added defense against bacteria and contaminants. With Oxidizing shock, you can use your pool after just 15 minutes!
If your pool is truly low in salt, then you can add salt at any time, but you need to use external sources of chlorine such as chlorinating liquid to shock your pool to kill the algae; you can't kill the algae in a bloom fast enough with an SWG alone..
The only time that it is important not to add salt is in the first 30 days after plaster is applied. Otherwise it is fine to go ahead and add salt. Run the pump for 24 hours after adding salt and turn off the SWG for those 24 hours.
Yes, a salt water pool has a reduced cost of operation as compared to a traditional chlorinated pool. This cost savings is primarily because chlorine is generated from salt and there is no need to buy chlorine. Additionally, salt water pools require fewer chemicals to keep the water clean and clear.
Wait until the shock process is complete, then put in the salt. It'll dissolve right away and be ready for the SWG by the time you get ready to use it.
Most recommend an ideal pH of 7.4–7.6 (7.2–7.8 acceptable), Total Alkalinity between 80–120 ppm, and Calcium Hardness around 200–400 ppm. Use water balancers to adjust your water into the proper ranges. Cyanuric Acid levels are very important for saltwater chlorinators.
If using 6% liquid chlorine bleach, add 5 gallons per 10000 gallons. Add the Shock: With the filter system running, and the pH on the low side, 7.2-7.4, add the chlorine (granular or liquid) slowly to the pool, dispersing it around the pool edge, or broadcasting the pool shock over the surface.
The answer really depends on the use conditions and how often you do maintenance on your pool. The safe answer is that they usually last for about five to seven years.
To reach the initial salt level recommended by the salt system manufacturer (usually 2400-3200 ppm), you will need to add about 200 lbs of pure pool grade salt (NaCl), per 10,000 gallons of water. Salt stays in the water, you only need annual boosters, to replace salt lost to backwashing or splashout.
While green algae are endemic in salt water pools, they are the easiest to kill. Green algae tend to grow during summers when the temperatures can get high. They float freely in the pool, making the water green. You might even see them growing on the bottom of the pool, on the walls, or in the crevices.
Maintenance Level of Difficulty
Is a saltwater pool easier to maintain than a traditional pool? Absolutely! As your salt chlorinator will do the work, you don't need to buy any chlorine, just add salt and you'll get clear and clean water.
Pros of Saltwater Pools
There's less chlorine and less of the heavy chemical scent and content. They're gentler on the skin, with less irritation to the eyes, hair and swimsuits. The water has a softer, silkier feel to it compared to chlorine water. They have lower maintenance costs than chlorine pools.
Some Misconceptions About Salt Water Systems
You need a special pump and filter to run a salt water pool. There is no such thing as a “salt water pump” or “salt water filter”; any pool pump or filter will do just fine.
People who use saltwater pools are still producing chlorine through saltwater generators. Saltwater will sanitize your pool, but it does so through electrolysis, which produces bacteria-killing chlorine. In other words, saltwater pools are no healthier or safer than chlorinated ones.
Lower pH by adding muriatic acid or sodium disulfide to the water, and raise it by adding baking soda (sodium bicarbonate) or soda ash (sodium carbonate). Check the total alkalinity of the pool water before raising pH. If it's near the acceptable range of 80 to 120 ppm, use soda ash.
A saltwater pool is an alternative to a traditional chlorine pool. Although you don't add chlorine tablets to a saltwater pool, it does still contain chlorine. It just has a smaller amount that's generated through the filter system. A saltwater pool contains 10 times less salt than the ocean.
You can convert your chlorine pool into a saltwater swimming pool and enjoy the benefits of salt water chlorination right in your own backyard. If your pool has a traditional chlorine sanitization system, you can easily switch to Hayward's advanced salt chlorination system.
To add salt, turn on your filter pump and add the salt directly to your pool water. Use a brush to help the salt dissolve and to prevent the salt from piling up on the bottom of your pool. Run your pump for 24 hours to help distribute the salt evenly throughout your pool.
The ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal. Before adding salt to your pool, test the water to check your salt level.