Many modern shower heads are designed specifically to increase the pressure of the water coming out of the showerhead itself. So, while they can't increase the actual water pressure of the home, they do improve the showering experience.
Most low-flow showerheads have a rubber pressure-reducing valve (called a regulator) to maintain a lower pressure. You can increase the flow by simply taking it out. You could also consider enlarging the hole that allows water into your showerhead with a drill to increase the amount of water coming through.
The most common cause of low shower pressure is a blocked showerhead, as a result of limescale build-up. These blockages obstruct the water flow, leading to reduced pressure over time. Most showers are fitted with a filter, protecting the pipework from debris, but this can become partially blocked by scale.
One of the simplest reasons for the lose of shower pressure is a blocked shower head. Shower heads accumulate mineral residue when the shower head is in use. Once the water has been shut off, over time these mineral deposits will bond together and create a limescale build up inside your pipes or shower head.
The short answer is low water pressure in your home arises due to a number of causes. Some include a shut or blocked water meter valve, mineral buildup clogs pipes, corroded pipes, or even a crack in the main city supply pipe to your home.
Open your main water valve.
Your house has a main water valve, usually located near the meter; the valve controls the flow of water into your home's pipes. Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure.
Depending on your current flow rate, you may be able to increase the flow simply by removing the filter or restricting device or replacing the showerhead with a higher-flow model, such as increasing to a standard 2.5 GPM head. Before you change the showerhead, make sure that the new model is legal in your area.
For water conservation purposes, most plumbing codes require faucets and showering devices to not exceed a certain maximum flow rate. Removing the flow restrictors could cause these devices to no longer meet these codes.
Differentiating Between Low Flow And High Flow Shower Heads
When it comes to Shower Heads, you'll typically find 2.5 GPM, 2.0 GPM, 1.8 GPM and 1.5 GPM. If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York.
While not all new shower heads come equipped with flow restrictors, they are critical in promoting energy efficiency and water savings.
A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
The Fire Hydrant Spa Shower Head Spa Plaza is a good replacement shower head that is designed to boost water pressure in low flow settings. It has a 4-inch face to provide wide coverage, and this enables the water to reach all parts of your body.
If low water pressure is affecting only your shower head, you should check for an obstruction in the shower head or see if your shower head has a water conservation filter installed. Otherwise when demand for water is high (such as in the morning or early evenings) pressure can be lower than during the rest of the day.
Check Your Aerator
If you have especially hard water, aerators become clogged with hard water buildup, a common cause of low water pressure in kitchen fixtures. Clean your aerator for a quick and easy DIY fix. Remove the aerator from the faucet using pliers and a towel (to prevent scratching).
Check for a pressure-reducing valve (PRV) mounted on your water main. Most come set from the factory for 50 psi, but you can adjust them up or down by turning a screw on top. PRVs can also go bad after 10 to 20 years. So if yours is old, it might be time to replace it.
If the low water pressure seems restricted to a single faucet or showerhead, the problem isn't with your pipes or water supply, but with the fixture itself. If it's a sink, the most common causes are a clogged aerator or clogged cartridge.
Typical household water pressure in the US is between 50 psi~ 80 psi, therefore often times the actual flow rate out of the shower head would be less than the flow rate rating because they are rated at 80 psi and your house setting is likely not.
If your water pressure seems low, the first step should be to test how much pressure you're actually getting from the shower head. A typical home's water pressure should be somewhere between 45 to 55 psi (pounds per square inch).
Many traditional showerheads offer an output of five or more gallons per minute, or gpm. With a low-flow showerhead system, the average is closer to 2.5 gpm, with some faucets offering amounts as low as 1.6, reducing the volume of water used in a single shower to a mere fraction of what was going down the drain before.