A GRAVEL BASE LAYER BEFORE SAND IS A MUST! Using sand alone to set pavers is not enough. The best and recommended paver base is 3/8-inch crushed gravel. The gravel provides a flexible base that absorbs ground tension to prevent frost heaves.
The paver bed is usually made of sand, 1/4″-10 crushed gravel, or synthetic material, and is the topmost paver support layer keeping pavers in place.
Dry laying allows porcelain pavers to be laid directly on grass and sand, but also on gravel, thanks to their reduced thickness of 20 millimeters that avoids the use of adhesives.
What Happens If You Don't Put Gravel Under Pavers? Drainage can really make or break an area where pavers are installed. If you have a paver patio, for example, without gravel or an alternative drainage system in place, water can roll back on it, causing damaging erosion.
One of the most important things needed for the proper installation of pavers is sand. It is necessary to prevent the joints of the pavers from moving. Just like all other construction installations, you also need a base for pavers if you want them to not move from their place.
Whilst it is technically possible to lay pavers on bare, unprepared ground, this practice is not recommended as the ground will shift over time, causing the pavers to develop a sunken look, or even crack.
Sand Bedding
Before laying the pavers, a layer of bedding sand is placed over the compacted base material. This layer provides a bed into which the pavers are set.
After you lay gravel, you'll need to spread a smooth layer of concrete sand for your pavers to settle in and stay. If you try to replace either of these aggregates with dirt, it won't be long before you have to tear it all up and start from scratch.
We suggest using 3/4″ gravel for the base. This can be either 3/4″ crushed stone or a 3/4″ recycled concrete product. Both products allow for adequate compaction and drainage—compact your gravel base with a vibrating plate compactor.
Since there is no gravel base, it's important to use a plate compactor to tamp down the soil before covering it with landscape fabric and a layer of sand. The sand layer must be screeded to provide a flat, properly sloped surface for the paver base panels. Lay the paver base panels over the sand bed.
Believe it or not, properly installed pavers are more structurally sound than concrete, and they can withstand much more weight and wear than blacktop. The traditional base for a paver patio is 4–6” of compacted gravel above your dirt.
The amount of sand you use can make or break your paver installation, so it's best that you use no more than the recommended 1 inch. Here's why: A sand layer that is too thick can create waves in your patio during the installation. Pressing pavers into a thick sand bed may result in misalignment and a messy look.
Pea gravel is very versatile, often used to cover driveways and fill spaces between stone pavers. It also serves as a good weed barrier and won't decompose like mulch.
FOUNDATION / BASE
If calibrated 30mm or greater paver is to be used, a suitable crush rock base can be used for pedestrian traffic, however, we recommend that the pavers be installed using a mortar bed rather than sand to give better stability to the finished product.
Laying pavers on sand base follows the same steps as laying them on soil base, but you'll be adding a layer of coarse sand, road base, or polymeric sand first. Rake the sand to even it out and use a plate compactor to make your sand base solid so you have a firm, stable base.
The guidelines are 4 to 6 inches for pedestrian walkways and 8 to 12 inches for driveways. Local soil conditions also impact depth needs. Generally, clay bases need to be dug deeper to facilitate drainage.
Concrete sand is the proper sand for laying a foundational base for a concrete paver installation. It is extremely coarse sand so it can be compacted uniformly and allows for adequate water drainage. Concrete sand will lift slightly into the joints of the pavers when they are being leveled, locking them into place.
Which is Better: Sand or Stone Dust? Sand is ultimately a much safer option than stone dust for paving projects. However, this is not a black-or-white issue. You may choose to use stone dust if you have a large supply of it, or prefer the texture and appearance of it.
The layer of sand should be from one to one and a half inches thick. The sand also needs to be dry, not wet. The layer of sand can be smoothed with the edge of length of board, such as a 2x4.
Crushed Stone
Stone aggregate comes in a variety of sizes, but most experts recommend 3/4-inch gravel for paver bases. Crushed stone makes a solid paver base because it allows water drainage and is easy to work with. Like sand, crushed stone comes in several varieties.
Porcelain pavers can be laid directly over existing grass or lawn as 'stepping stones' or to create a pathway, but for better stability of the pavers, the grass beneath the pavers should first be removed, together with a shallow layer of the topsoil.