There is no way to replace the fascia board without removing the gutters, as the gutters are mounted to the board. So, your roofers will carefully remove the gutters.
Yes, gutters first. But gutters cover fascia on eaves, so that means fascia need to be done first, then gutters.
Yes, it is possible to replace a fascia board without removing the gutters. However, the specific method may depend on the construction of your gutters and fascia board. It is recommended to consult with a professional or follow manufacturer guidelines for the best approach in your situation.
No, you don't necessarily need to replace your gutters when installing a new roof, but it's a good time to assess their condition. If your gutters are damaged, rusted, or improperly draining, it may be beneficial to replace them to ensure optimal performance and protect your home from water damage.
If your fascia board is attached to a drip edge, remove it carefully using a pry bar or utility knife. The drip edge helps protect the fascia board against water damage and directs water away from the roof decking.
There is no way to replace the fascia board without removing the gutters, as the gutters are mounted to the board. So, your roofers will carefully remove the gutters. Typically, the same gutters can be re-installed on the new fascia board, if they are in good condition.
Can You Install Drip Edge without Removing Gutters? Yes, you can. The drip edge is installed under the roof shingles and hangs over the gutters. Loosen the bottom part of the shingle with a putty knife, install the drip edge and secure it with a roofing screw from the top.
Gutters often are attached to fascia, which in turn are interlocked with the soffit boards. This means you'll need to remove your gutters before you can pull back the fascia and work on the soffits.
If your home is on a slope that directs rain away from the foundation, you may not require gutters. If your gutters require frequent cleaning and repairs due to blockages, damage, or other issues, removing them may be cheaper and more accessible. This is particularly significant in densely forested areas.
A gutter expert is another professional who can provide soffit repair or fascia replacement.
If you are careful, you do not “have” to remove your gutters. However, if you are worried that you might get paint on them and want them out of the way, then it is best to remove them. Beware, though, that removing them yourself, or allowing a painter to remove them can void your Byers LeafGuard Gutter System warranty.
Replacing your fascia is often pricier, but for good reason – this guarantees a longer lasting solution and is more cost effective in the long run. This is because the guarantee offered with capping of fascia does not typically cover the sub-structure.
When your roof is replaced, the roofing contractor will typically inspect the fascia boards to determine if they're in good condition. If the fascia is damaged or deteriorating, they'll replace it to ensure it can support the new roof system properly.
Unscrew the gutters from behind your existing fascia board with an electric screwdriver. Then, locate the brackets underneath your gutter holding them in place and unscrew them so you can lift the gutter up and away from the fascia. Remove the gutter brackets from your fascia so you can reuse them on the new board.
Fascia board replacement typically costs between $7 and $22 per linear foot, with an average of around $14.60, including materials and labor.
No, there should not be a gap between the drip edge and the fascia board. If there is a noticeable gap, it could indicate that either the drip edge or the fascia needs to be adjusted so that they align properly with each other.
According to Owen's Corning Roofer's Guide to Installation, “2012 International Residential Code (IRC) requires drip edge at the eaves and rake edge of the roof. The IRC has required drip edge since the 2009 edition”.
Silva recommends installing the drip edge so the edge of the roof is 1 1/2 to 1 3/4 inches away from your fascia board. This way, water can drop freely instead of seeping back into the fascia. “It won't drop if it does get blown in there from wind, but it's really not going to be surface tension,” Silva says.
However, it also depends on if you're getting fascia work done during your roof replacement. If you are, the gutters in the area will be removed to repair or replace the fascia board(s). But under normal circumstances, they shouldn't be removed if you're only replacing your roof.
Gutter installers in frost-free zones simply screw the inside edge of gutters through the fascias to the extreme ends of rafters. This can be sufficient to withstand the weight of rainwater, provided the downpipes are clear and the water can flow freely away.
Firstly remove the gutters if they aren't made of cast iron and give them a good clean. Now's the time to repair any soft or rotten woodwork before repainting.
Apply a continuous bead of caulk along the joint between the top edge of the gutter and the fascia board. Use your finger to smooth the caulk, and make sure the gap is completely covered. Allow the caulk to dry according to the manufacturer's instructions.
Back in my construction days, I learned that you place the tar paper OVER the drip edge on the eaves so if moisture gets through the shingles, it does not get under the drip edge.
If you're getting both done, which we estimate happens 35% to 50% of the time, we replace the roof first and then install the gutters.